Stratogel 3D - Insulator for 3D models 100ml

Isolator for 3D models.

Characteristics:

• gel, despite its viscosity, spreads easily on the surface, and after drying creates a thin layer;
• acts as a separating film between 3D resin and acrylic resin;
• has the appropriate viscosity, effective with just one layer;
• however, you can apply a second layer when dealing with rougher surfaces (printed models larger than 100 microns);
• the first layer must be completely dry;
• the plastic layer is easily removed with water and a brush.

STRATOGEL comes off without residue, does not damage acrylic resin and 3D resin, does not change the properties of resins, is safe and does not contain any toxic substances.

Advantages:

• easy application: a single layer is applied with a brush;
• creates a very thin insulating layer;
• does not contaminate 3D resin or acrylics;
• easily removed with water.

How to use:

• apply a few drops directly from the bottle to the dry model and spread evenly with a brush;
• For quick drying, it is recommended to dry the gel with compressed air at low pressure for 30 seconds, air drying for 30 minutes.

Packaging:

• 100ml

Formlabs Soft Tissue Starter Pack

Soft tissue starter pack.

• Thanks to the Soft Tissue Kit, you can print elements imitating soft tissues. The material is used to print flexible gingival masks for use in conjunction with rigid dental models to aid in the planning of implant procedures. The Soft Tissue set consists of a flexible base resin (Flexible 80A) and pigments that allow you to obtain various degrees of color saturation, from dark to light pink shades. Magenta pigment, yellow pigment and white pigment can also be purchased separately.

Packaging:

• 1set

Otoflash G171-6 N2-Connecting kit

Connection and connector for gas cylinder (Nitrogen).

Packaging:

• 1 pc.

Detax resin Freeprint crown 500g

Light-curing resin with ceramic filling for 3D printing. For the production of permanent crowns, inlays, onlays, veneers, prosthetic teeth and long-term temporary crowns and bridges. For DLP printers with a wavelength of 385 nm. Does not contain MMA and THF-MA. Class IIa medical device.

Advantages:

• Very high resistance to breakage and abrasion.
• Natural translucency and opacity.
• Easy to grind and polish.
• High biocompatibility.
• No discoloration thanks to low water absorption.
• Long-term colour stability.
• Excellent bonding with classic dental cements.

Physical data:

• Bending strength > 115 MPa.
• Modulus of elasticity > 2800 MPa.
• Final hardness > 50 Barcol.
• Water absorption at 40 g/mm3.
• Solubility 7.5 g/mm3.

Packaging:

• 500g

Dreve Resin vat for Phrozen Sonic XL4k

Resin bathtub.

Packaging:

• 1 piece.

Dreve FEP foil for Phrozen Sonic XL 4K

FEP blank - special FEP foil for Phrozen printer.

Technical specifications:

• material: FEP;
• color: transparent;
• size: 290x210mm.

Packaging:

• 1pc.

Dreve resin FotoDent biobased model 385nm beige opaq 1kg

Biobased® 385nm model

Biobaset t® model is a light-cured resin consisting of 50% renewable raw materials. The material properties are ideal for the production of models (also the above-mentioned Aligner). The FotoDent® bio-based model can be cleaned using the FotoClean program.

Advantages:

• Less pollution in the atmosphere.
• Free from carcinogenic materials.
• Shorter cleaning times.

Material data:

• Color beige opaque.
• Modulus of elasticity ≥ 2200 MPa.
• Viscosity ~ 0.6 Pa s.
• Bending strength ≥ 95 MPa.

Packaging:

• 1kg bottle.

Formlabs Dental Model V3 Form 3 1L 3D Printer Resin

Designed for crown and bridge models with replaceable stumps.

Dental Model Resin is a very precise resin with high accuracy.

Version 3:

• This version of Model Resin is a reformulation of the previous version;
• With the new V3 resin, you can print even more accurate models in half the time;
• supports print resolutions: 100 and 50 microns;
• Requires Form 3 Resin Tank V2.1 or later for Form 3B and Form 2 Resin Tank LT for Form 2.

Packaging:

• 1l

Note: The current price promotion (discount) is valid only for products available from stock or until December 31, 2026.

Simplex model isolation 80g

SIMPLEX model isolation, Isolator for 3D printed models from resins and filaments.

Renfert catalog number 17350010

Thanks to the ready-to-use agent, you can easily and safely make orthodontic appliances from dental resin on a printed model.

Apply a thin layer of the agent with a brush.

Once dry, this layer creates a clear isolation between the printed model and the dental acrylic.

Advantages:

• adapted for use with models printed from 3D filament and resin;
• intended for isolating models in the production of removable orthodontic appliances;
• also suitable for models made in the SLA/DLP printing process;
• One application is enough to achieve optimal separation of the model from the workpiece;
• the agent can be easily removed with water and does not require steam cleaning;
• does not contain substances harmful to health.

Packaging:

• 1pc/80g

Senertek resin for temporary crowns Temp V5 500g

Senertek TEMP is a high-quality light-cured resin designed for 3D printing of temporary dental restorations such as crowns and bridges.

This material offers a perfect combination of aesthetics, durability and functionality.

Characteristics:

• natural aesthetics: all shades provide a high-quality aesthetic finish that blends harmoniously with the patient's natural teeth;
• strength and stability: provides crack-resistant temporary restorations with high hardness and low shrinkage;
• biocompatibility: safe for intraoral use, does not cause adverse reactions;
• Versatile: ideal for a wide range of temporary dental applications such as crowns, bridges and veneers;
• for use in printers with DLP, SLA, LCD technology;
• visible on X-ray photographs;
• filled with 40% nanoceramics;
• does not change color over time.

Application:

• for temporary removable dental prostheses;
• individual temporary crowns;
• contributions, outlays;
• temporary bridges;
• temporary veneers.

Resin parameters:

• bending strength: 260 MPa;
• water absorption: <20μg/mm³;
• water solubility <1.2μg/mm³;
• hardness: 95 Shore D;
• viscosity : 1900 CPS.

Packaging:

• 500g

VarseoVest C&B 160g

VarseoVest C&B high-temperature precision investment material for casting 3D printed crown and bridge frameworks.

Advantages:

• excellent fit and smooth surfaces of cast objects;
• very good flow properties and long processing time enable easy shielding of printed objects;
• great time saving during the heating process, directly into the furnace heated to 900 °C, time 20 min;
• high strength of the covering mass – the sleeves do not crack or tear despite the expansion of the plastic;
• Clear expansion control using the special BegoSol ® CC mixing fluid ensures reproducible fitting results.

Physical data:

• processing time: approx. 3 min 15 sec;
• flow properties 140 mm;
• linear thermal expansion: 1.3%;
• Compressive strength: approx. 5 MPa.

Packaging:

• 1pc/160g

BegoSol CC liquid for investment 1000ml

Begosol CC liquid, compatible with VerseoVest C&B mass.

Packaging:

• 1l

VarseoVest P plus 300g protective mass

VarseoVest P plus, designed for embedding 3D-printed skeletal prosthesis structures.

Advantages:

• Perfect fit and smooth surfaces of cast objects.
• Excellent flow properties and long processing time enable easy shielding.
• Great time saving in the heating process; placed in the preheated oven after 20 minutes at 800–950 °C.
• High resistance of the covering mass – the sleeves do not tear or crack despite the expansion of the plastic.
• Varseo Vest P is characterized by reduced dust formation during processing, which contributes to a significant reduction of harmful quartz and cristobalite dust in the laboratory.
• Cures with edge stability, good release.
• Clear expansion control using the special BegoSol ® K mixing fluid ensures reproducible fitting results.

Physical data:

• Preparation time: approx. 4 min 40 sec.
• Flow properties: 145 mm.
• Linear thermal expansion: 0.9%.
• Compression resistance: approx. 8 Mpa.

Packaging:

• 1pc/300g

Dreve FotoDent denture resin 385 nm pink transparent 1kg

Light-curing resin for the production of denture bases.

The material provides accurate results with exceptional dimensional stability.

The FotoDent® denture is MMA-free and color-stable.

Material data:

• Final hardness 80 Shore D.
• Elastic modulus > 2000 MPa.
• Bending strength > 80 MPa.
• Viscosity 0.4-0.6 Pa·s.
• Transparent pink color.

Packaging:

• 1 kg

Black ziplock bags for storing 3D prints 12x18cm 50 pieces

Black zipper bags for storing models and other 3D prints.

• Size 12x18cm.

Packaging:

• 1 pack/50 pcs.

AnyCubic Wash & Cure Machine 3.0 (4L)

The washer is compatible with most LCD 3D printers including Elegoo Mars, Phrozen Sonic, and other printers.

Compared to Wash & Cure 2.0, the curing size has increased by 15% and the capacity of the cleaning basket by as much as 100% (up to 3L).

Advantages:

• large capacity of 3l basket and 4l bucket;
• large cleaning work area in the basket 165 x 100 x 180 mm;
• the cleaning and curing mode is easily accessible on the panel, the knob sets the working time to max. 30 minutes;
• Thanks to the innovative FlexiCure gooseneck lamp, UV light can reach every spot;

Technical data:

• cleaning area in basket: 165 x 100 x 180 mm;
• cleaning area in basket (suspended): 165 x 100 x 165 mm;
• curing area: 160x180 mm;
• device size: 290x270x479 mm;
• gooseneck light: Max. height 285 mm;
• time selection range: 1 - 30 min;
• bucket capacity: 4L;
• basket capacity: 3L;
• UV light wavelength: 405 nm;
• weight: 2.7 kg.

Packaging:

• 1pc

Formlabs Precision Model (Form4) 1l 3D Printer Resin

This next-generation precision model printing resin, developed specifically for the new Form 4 ecosystem, is a high-accuracy material that creates beautiful models with crisp edges thanks to its high opacity, beige color, and smooth, matte finish.

Precision Model Resin is the next generation of model resin for the new Form 4 series of printers, printing three times faster while offering improved accuracy and aesthetics.

Advantages:

• prints eight models in just 90 minutes;
• 5-minute cycle in the washer;
• 5-minute cure at room temperature.

Compared to Model Resin V3, Precision Model Resin is:

• greater accuracy - better resolution and consistency of small elements;
• speed - designed to leverage the new Form 4 ecosystem for three times faster printing;
• more opaque and matte aesthetic to better highlight edges.

Packaging:

• 1l

Note: The current price promotion (discount) is valid only for products available from stock or until December 31, 2026.

Detax resin Freeprint splintmaster taff 1000g

Light-curing, flexible resin for 3D printing. For making flexible splints, repositioners, mouth guards, splints and bite plates. Biocompatible. For DLP printers with a wavelength of 385 nm. Class IIa medical device.

Advantages:

• Very high wearing comfort.
• No stress.
• Long-lasting durability and stability.
• High impact resistance.
• Easy to maintain, clean and polish.
• No MMA, THF-MA and TPO.
• Odor and taste neutrality.

Physical data:

• Tensile strength > 40 MPa.
• Elongation > 20%.
• Tear strength > 140 N/mm.
• Final hardness > 75 Shore D.
• Water absorption < 32 µg/mm³.
• Solubility < 5 µg/mm³.

Packaging:

• 1000g

Detax resin Freeprint splintmaster flex 1000g

Light-curing, very flexible 3D printing resin. For making flexible splints, repositioners, mouth guards, splints and bite plates. Biocompatible. For DLP printers with a wavelength of 385 nm. Class IIa medical device.

Advantages:

• Very high wearing comfort.
• No stress.
• Long-lasting durability and stability.
• High impact resistance.
• Easy to maintain, clean and polish.
• No MMA, THF-MA and TPO.
• Odor and taste neutrality.

Physical data:

• Tensile strength > 25 MPa.
• Elongation > 50%.
• Tear strength > 110 N/mm.
• Final hardness > 65 Shore D.
• Water absorption < 32 µg/mm³.
• Solubility < 5 µg/mm³.

Packaging:

• 1000g

Detax resin Freeprint temp 500g

Light-curing, biocompatible resin for printing temporary crowns and bridges.

Advantages:

• Light spectrum 385 nm.
  • Exceptional resistance to cracking and bending.
  • High abrasion resistance.
  • Natural tooth aesthetics, shiny, translucent colors.
  • Easy surface treatment and polishing, which can be characterized individually with composites.
  • Low viscosity ensures low material consumption and faster cleaning.
  • Resistant to conditions in the oral cavity, no odor and taste irritation.
  • Class IIa medical device.
  • Colours: A1, A2, A3.

Packaging:

• 500g

Detax resin Freeprint splint 2.0 500g

Light-cured, biocompatible 3D printing resin for the production of implantology templates, transfer keys and bite splints.

Advantages:

• Light spectrum 385 nm.
• Transparent formula for visual control in the work area.
• Process reliability due to high initial hardness and final strength.
• Low viscosity ensures low material consumption and faster cleaning.
• Highest mechanical resistance to bending and cracking.
• Smell and taste neutral.
• Medical device class IIa,
• Colour: transparent.

Packaging:

• 500g

Detax resin Freeprint model 2.0 1000g

Light-curing 3D printing resin for dental models.

Characteristics:

• for DLP printers with a wavelength of 385 nm;
• maximum surface hardness and shape stability ensure excellent mechanical load-bearing capacity;
• faster workflow without drying process;
• maximum precision of construction, sensitivity and stability meet the high requirements of model production;
• optimal edge strength ensures reliable models;
• colors: white.

Physical data:

• bending strength > 80 MPa;
• modulus of elasticity > 1700 MPa;
• final hardness > 80 Shore D.

Packaging:

• 1000 g

Detax resin Freeprint cast 2.0 500g or 1000g

Light-curing 3D resin for manufacturing precision casting objects (skeletons).

Advantages:

• For all UV printers with a 385 nm light spectrum;
• Excellent dimensional stability after printing ensures safe application with fit control, especially for cast models and molds;
• Print results are precise and distortion-free, even for extremely delicate and complex models;
• Any corrections or repairs after printing are possible using easyform gel LC;
• Low viscosity and optimized cure depth help reduce printing time and material consumption and facilitate faster cleanup;
• It burns without leaving any residue in the mould and is the basis for high-quality modelling results that ensure a perfect fit;
• Colour: red.

Packaging:

• 500g or 1000g

Keystone resin KeySplint Soft 1kg

KeySplint Soft resin is fully biocompatible and complies with international regulations and standards for medical devices.

Using unique technologies, Keystone Industries has developed a one-of-a-kind 3D printing resin for the production of flexible dental trays, night guards and whitening trays.

This DLP-optimized resin is a unique printing material that combines the strength needed to protect teeth from disorders like bruxism with added flexibility for increased patient comfort.

KeySplint Soft is also easy for the patient to clean.

Characteristics:

• can be printed on the Mars 5Ultra 9K printer (micran code 8572);
• solid formula allows for three years of guaranteed shelf life;
• is color stable and has been proven in many open-source printers.
• no other dental splint resin offers the quality and performance of KeySplint Soft.

Advantages:

• biocompatible;
• transparent;
• easy to polish;
• resistant to discoloration.

Physical data:

• flexural strength 2.6-4.4 MPa (ISO 20795-2);
• Young's modulus 1356 MPa (ASTM D790);
• final hardness 82 Shore D;
• water sorption <18 µg/mm³ (ISO 20795-2).

Packaging:

• 1kg

Formlabs Work platform for Form 4

The Form 4 work platform has a durable aluminum surface. A spare platform can speed up your workflow and allow for uninterrupted printing, whether you're changing resins or starting a new print.

Packaging:

• 1 piece

Formlabs Resin Standard V4 (Form 3) 5L

Standard resin.

Color:

• Clear;
• Gray.

Perfect shape reproduction, durability and excellent surface quality.

Packaging:

• 5l

Note: The current price promotion (discount) is valid only for products available from stock or until December 31, 2026.

Screen Protector EcoPrint 5 pieces

Cover for EcoPrint printers mounted on the LCD screen to protect against spilled resin and mechanical damage.

This will prevent scratches, cracks and other damage from appearing on the screen.

The cover has high light transmission, so the prints are precise and accurate.

Fits Saturn 4 Ultra 16 K and Mars 5 Ultra printers but requires cutting.

Packaging:

• 5pcs

Anycubic EcoPrint foil for resin tank 1 piece

Resin tank foil for Anycubic EcoPrint.

Characteristics:

• Size 278 x 190mm.
• Thickness 0.3mm.
• Permeability 92%.
• ACF foil type.

Advantages:

• Suitable for fast printing.

Attention:

• The foil is a consumable part and must be replaced if it is deformed or damaged during printing.
• The foil should be replaced immediately if any signs of deformation or excessive adhesion occur.

Packaging:

• 1 piece

Anycubic Eco Print foil for resin tank, 2 pieces

Resin tank foil for Anycubic EcoPrint.

Characteristics:

• Size 278 x 190mm.
• Thickness 0.3mm.
• Permeability 92%.
• ACF foil type.

Advantages:

• Suitable for fast printing.

Attention:

• The foil is a consumable part and must be replaced if it is deformed or damaged during printing.
• The foil should be replaced immediately if any signs of deformation or excessive adhesion occur.

Packaging:

• 2 pcs

Anycubic EcoPrint resin tank 1 piece

Resin tank for EcoPrint resin tank.

Packaging:

• 1 piece

Formlabs VarseoSmile TriniQ Resin 750g (Form 4B)

Formlabs BEGO™ VarseoSmile® TriniQ® resin is a versatile, biocompatible ceramic-filled material designed for both temporary and permanent restorations, including single-piece restorations such as crowns, inlays, onlays, veneers, bridges and dentures.

BEGO™ VarseoSmile TriniQ is the first 3D printed resin for fixed bridges, characterized by excellent accuracy, translucency and an efficient process.

Available in three VITA shades:

• A2;
• A3;
• B1.

Printer Compatibility: Form 4B

• compatible with Form 4 resin tank;
• compatible with the Form 4 Flex build platform;
• has a certificate of biocompatibility.

Material properties

• bending strength: 120 MPa;
• flexural modulus: 3600 MPa;
• Shore hardness: ≥ 90 D;
• sorption: < 0.6 µg/mm³;
• Solubility: < 12 µg/mm³;

Packaging:

• 750g.

Note: The current price promotion (discount) is valid only for products available from stock or until December 31, 2026.

V-Print splint comfort clear 1000 g

Light-curing resin for printing thermoelastic, therapeutic dental splints.

Indications:

• Therapeutic splints.

• Diagnostic auxiliary and functional elements.

• Teeth whitening trays.

• Palatal plates.

Advantages:

• High flexibility and abrasion resistance - exceptional break resistance and durability.

• Excellent comfort of use, the material is thermoelastic and tasteless and odorless.

• Transparent – for making rails that are almost invisible.

• Easy to polish.

• Biocompatible.

• Class IIa medical device.

Packaging:

• 1000g

V-Print dentbase pink 1000 g

Light-curing resin for printing removable denture plates.

Indications:

• Removable denture plates

Advantages:

• Class IIa medical device

• Comfort of wearing the prosthesis – thanks to precision of workmanship and perfect fit.

• High aesthetics – natural gingival color.

• Compatibility – use with available lining materials.

• Safe removal from build platform.

• Patient acceptance - no taste or smell.

• Biocompatibility.

Packaging:

• 1000g

Ivotion Base Print 3D printing resin for denture plates 1000ml

Aesthetic base material for 3D printed prostheses, enabling efficient production of prostheses in proven PMMA quality.

Ivotion Base Print is the first 3D printing material for permanent applications from Ivoclar (material quality meets the requirements of the EN ISO 20795-1 standard.)

Drawing on Ivoclar's extensive experience in materials, Ivotion Base Print provides high-quality, durable and aesthetic denture bases with exceptional wearing comfort and high accuracy of fit.

Characteristics:

• Ivotion Base Print is available in three shades, allowing you to create individual dentures with a natural look;
• the material is characterized by a low tendency to plaque formation and discoloration.
• Ivotion Base Print can be used in the PrograPrint system and other approved printing systems within the approved process: Ivoclar: PrograPrint PR5, Asiga: Max, Max 2, MAX X, Ultra, Pro 4K, Pro 4K XL.

Packaging:

• 1000ml

Formlabs Form 4 Finish Kit

Quickly and easily finish your prints with the versatile Form 4 Finishing Kit, which keeps your workspace clean and organized. Includes two rinse tanks, a rinse basket, a resin removal tool, a plastic tank scraper, a build plate tool, cutters, a squeeze bottle, and disposable nitrile gloves.

Packaging:

• 1 set

Note: The current price promotion (discount) is valid only for products available from stock or until December 31, 2026.

AnyCubic Wash & Cure 3 Plus (7.6L)

Device with a large capacity of 7.6 L.

It allows you to wash your prints in two ways - using a basket or in hanging mode, without removing them from the build platform.

Advanced features such as adjustable UV lighting time and intensity ensure efficient and even light distribution on the print.

Advantages:

• large capacity 7.6l;
• maximum working area is 228x128x300 mm;
• Thanks to the innovative FlexiCure gooseneck lamp, UV light can reach every spot;
• The touch screen makes it easy to control the print washing and curing processes.

Technical data:

• washing function working area (in the basket): 228 x 128 x 260 mm;
• washing function working area (with platform): 228 x 128 x 250 mm;
• curing function working area: 220 x 260 mm;
• UV light source: 14 lenses 405 nm + Flexicure lamp;
• print washing and drying time: 1 to 30 minutes;
• rated power: 36 W;
• device dimensions: 312 x 267 x 434 mm;
• weight: 5.7 kg.

Packaging:

• 1pc

V-Print Try-In beige 1000 g

Light-curing resin for the production of trial prosthetic restorations.

Indications:

• Trial full and partial dentures.

• Transfer and sanding templates.

• Corrective and occlusal impressions.

Advantages:

• Initial check-up before making the final prosthesis – checking and, if necessary, adjusting and correcting occlusion, function, pronunciation and aesthetics.

Packaging:

• 1000g

Formlabs Form Wash (2nd Generation)

Form Wash automatically cleans printed items thoroughly and effectively using IPA (isopropyl alcohol) or alternative solvents.

Characteristics:

• prints can be transferred directly on the build platform from the printer to Form Wash or removed and placed in the washing basket;
• prints are precisely and thoroughly mixed in the solvent using a rotor, thanks to which every nook and cranny is perfectly clean;
• Once the wash is complete, Form Wash automatically lifts the models from the IPA so they can dry.

Packaging:

• 1 pc.

Note: The current price promotion (discount) is valid only for products available from stock or until December 31, 2026.

Formlabs Form 4B 3D Printer 2026 Edition Open Material Mode Included!

Formlabs printers purchased after January 19, 2026 are equipped with Open Material Mode as standard (open system, ability to print on any resins).

The Form 4B 3D printer is another offering from Formlabs. Never before has the dental and medical industries had access to such a combination of quality, speed, and user experience in a desktop printer.

Formlabs Form 4B with new LFD™ technology

The Form 4B printer features the newly patented Low Force Display™ technology. It features six advanced print control systems, a new resin tank and dispensing system, and a larger build plate than previous models. The new build plate dimensions are 200 x 125 x 210 mm, which is 30% larger than before.

Printing speeds of up to 100 mm/h deliver finished models in less than 2 hours. A 50-micron pixel size is used for maximum dimensional accuracy.

The Form 4 3D printer is a solution designed for the dental and medical industries. The Form 4B supports all materials available for engineering Form 4 printing, plus dental, medical, and biocompatible resins. A wide selection of materials will find use in the daily work of dental technicians, dentists, and medical research laboratories. The combination of the speed of new LFD technology, high-quality print surfaces, and specialized materials expands the possibilities for digital medicine and dentistry. From medical scan to print in 2 hours? - now possible with the new Form 4B printer.

The most important benefits of the new Form 4B series compared to previous models:

• New 3D printing technology – Low Force Display™
• Save time – print parts up to 5 times faster.
• Cheaper operation – lower resin tank costs with extended service life and 27% lower cost of basic materials
• Larger work area – 30% larger work platform with dimensions of 20×12.5×21cm.
• Greater dimensional accuracy – new optical engine.

Technical specifications:

• Technology: Low Force Display™ (LFD)
• Working area: 20.0 × 12.5 × 21.0 cm
• Layer thickness: 25 – 300 microns
• XY resolution: 50 microns
• Average printing speed: 40 mm/h
• Maximum printing speed: 100 mm/h
• Resin Tank Life: 75,000+ layers with any Formlabs material
• Printer weight: 18.3 kg
• Printer dimensions: 39.8 x 36.7 x 55.4 cm
• Warranty and service: one-year warranty included
• Paid service and extended warranty options: available

• Accepted file types: STL, OBJ, 3MF

  Packaging:

• 1x printer

• 1x Resin Tank form 4B
• 1x 4B mold build platform
• 1x Mixer form 4B
• 1x Finish kit

The printer comes with a 1-year warranty as standard, but you can also purchase a DSP (Dental Service Plan) package that extends the warranty to 3 or 5 years.

Other benefits of Dental Service Plan:

Priority Technical Support: Access to Formlabs' dedicated support team, specialized in dental applications. Requests are handled faster than with a standard warranty, which is crucial for clinical or laboratory work.

DSP's extended warranty extends your printer's standard warranty for the full duration of the plan. This protects against unexpected repair costs and provides greater cost stability.

Quick device replacement (advance replacement/hot swap). In the event of a failure, Formlabs ships a replacement device before the damaged printer is returned. This minimizes downtime and allows for continuous operation in the practice or laboratory.

Dedicated support for dental workflows Support covers not only the printer itself, but also software, materials certified for dental applications, and the correct configuration of printing and post-processing processes.

Training and Educational Materials Access training, documentation and videos to help you implement your printer more quickly and achieve consistent, high-quality prints.

Proactive diagnostics and consulting Regular check-ins and support in identifying potential problems before they impact print quality or device availability.

Greater operational safety In the dental environment, where printers are used for items that directly impact patient treatment, DSP increases reliability and predictability.

Note: The current price promotion (discount) is valid only for products available from stock or until December 31, 2026.

SG Surgical Guide Next Dent resin orange 1kg

NextDent SG Surgical Guide is a biocompatible class I material developed for printing surgical guides.

Due to their high accuracy, they facilitate insertion of the sleeve immediately after printing.

This allows for even greater precision during surgery.

NextDent SG material is resistant to disinfectants.

The material can also be sterilized using gamma radiation and autoclave.

The use of an autoclave does not affect the dimensional stability of the material.

Technical data:

• material strength ≥ 85 MPa;
• tensile strength ≥ 2118 MPa
• residual monomer < 0.1;
• biocompatible, non-toxic;
• orange color.

Packaging:

• 1kg

Formlabs Form 4 Mixer

The Form 4 resin mixer improves material efficiency by maintaining resin homogeneity in the tank during the printing process.

A mixer is required for every print.

For convenience, we recommend having one resin mixer per tank.

Packaging:

• 1 pc.

Note: The current price promotion (discount) is valid only for products available from stock or until December 31, 2026.

Formlabs Solvent Pump for Form Wash (2nd Gen)

The Solvent Pump is a battery-powered pump that quickly fills and empties the Form Wash container.

Solvent Pump eliminates the risk of chemical leaks and simplifies workflow.

printer compatibility:

• Form 4, Form 4B, Form 3, Form 3L, Form 3B, Form 3BL, Form 2.

Packaging:

• 1 pc.

Note: The current price promotion (discount) is valid only for products available from stock or until December 31, 2026.

VarseoSmile TriniQ 3D resin 250g

VarseoSmile TriniQ resin is distinguished by its innovative composition, and thanks to the high stability of the material, it allows the printing of not only permanent bridges, but also extensive temporary restorations.

Excellent polishing properties and exceptional translucency guarantee the highest aesthetics.

Advantages:

• high bond strength with conventional adhesive cements ensures reliable seating in the patient's mouth and long-term use of restorations;
• The efficient 3D printing process enables the quick and productive production of restorations, reducing treatment times and enabling the successful treatment of more patients.
• The exceptional stability of the material enables the creation of durable and highly aesthetic restorations. It enables printing of temporary and permanent crowns and bridges;
• excellent polishing properties and translucency enable the creation of restorations that blend seamlessly with natural teeth;
• the resin has a degree of abrasion similar to lithium disilicate and is also friendly to opposing teeth;
• it is not only durable, but also optimally integrates with the natural tooth structure;
• ease of restoration and repair using conventional composites increases the long-term stability of the restoration and optimizes treatment flexibility;
• excellent color stability ensures lasting aesthetic effects;
• With exceptional biocompatibility and a double bond conversion rate of almost 100%, it outperforms most composite materials.

Technical Data:

• colors according to the Vita shade guide;
• viscosity 1900-6000 mPa*s;
• bending strength 120 MPa;
• water absorption 12.00 µm/mm³;
• water solubility 0.06 µm/mm³;
• surface hardness >90 Shore D;
• curing wavelength 385 – 405 nm.

Packaging:

• 250g

AnyCubic Wash & Cure Plus Machine (washer/lamp)

"Turnip" washer and UV lamp for printed models.

Technical specifications;

• Control method: digital tube, LED indicator, control knob;
• rated power: 40 W;
• input voltage: AC110/240V 50/60Hz;
• UV light length: 405nm;
• time selection: 1-60 min;
• Machine size: 290mm(L)270mm(W)479mm(H);
• Washing basket size: 192mm(L)120mm(W)290mm(H);
• maximum size of the object to be hardened: 190 mm (D) * 245 mm (H);
• Weight; ~6.5 kg.

Packaging:

• 1pc

Formlabs Resin Pump

Formlabs resin pump.

The Form 3 Series Stereolithography (SLA) 3D Printer Resin Pumping System seamlessly delivers resin from a 5L resin pack via a pumping system directly to the printer's reservoir.

Reduce waste by 86%.

Packaging:

• 1 pc.

Note: The current price promotion (discount) is valid only for products available from stock or until December 31, 2026.

AnyCubic screen protector for Photo Mono X 6K 5 pcs

A cover mounted on the LCD screen to protect against spilled resin and mechanical damage.

This will prevent scratches, cracks and other damage from appearing on the screen.

The cover has high light transmission, so the prints are precise and accurate.

Packaging:

• 5pcs

Formlabs Resin Tank for Form 4

Each resin tank includes a reusable lid that makes it easy to stack the tanks and store the resin outside of the printer.

With a separate tank for each color or resin type, changing materials is as simple as inserting a new tank.

Resin tanks provide consistent performance for at least 75,000 print layers (typically 1-2 years for the average user).

Packaging:

• 1 pc.

Note: The current price promotion (discount) is valid only for products available from stock or until December 31, 2026.

Resin tray 20x25x10cm

Resin tray 20x25x10cm

Packaging:

• 1 piece

Resin strainer

Convenient strainer for draining the remaining resin after printing.

Packaging:

• 1 piece.

Thermometer Hygrometer LCD

Thermometer and humidity sensor.

Thanks to this device, it is possible to measure the environmental conditions in which e.g. resin for 3D printers and many other materials sensitive to humidity and temperature are stored and used.

Technical data:

• Product type: Temperature and humidity sensor.
• Connectivity: Bluetooth 4.2 LE.
• Power: CR2032 battery.
• Rated voltage: 2.5V - 3V.
• Humidity range: 0%~99%RH.
• Temperature range: 0ºC ~ 60ºC.
• Material: ABS, PMMA.
• Certifications: QB/WSDJ 2401-2019.
• White color.
• Dimensions: 43x43x12.5mm.
• Additional information: Temperature display every 0.1ºC, Humidity display every 1% RH

Packaging:

• 1 piece