TD Master-Cast Tooth Strainer
A strainer for setting and scalding teeth using the infusion method.
The arrangement of the teeth in a specific pattern makes it impossible to mix them up.
Characteristics:
- internal dimensions: 105 x 80 x 50 mm.
Packaging:
- 1 pc.
Groove bur Master Cast 1 piece
Milling cutter for creating retention in artificial teeth.
Retention strengthens the connection between the teeth and the denture plate.
**Characteristics:
- 2.35 mm shank, for handpiece;
- revolutions 5,000 – max. 15,000 min-1.
Packaging:
- 1 pc.
Vertex Castavaria 1000g
Vertex Castavaria pressure-curing acrylic for the production of full and partial dentures using the pouring technique.
Characteristics:
- minimized shrinkage;
- color stability;
- extended liquid phase.
Application:
- complete dentures;
- skeletal prostheses.
Technical data:
- dough phase: 8 <…> 9 minutes;
- working time: 13 minutes;
- curing time: 30 minutes at 55°C and 2.5 bar pressure;
- mixing ratio by volume/parts by weight: 1 ml / 0.95 g liquid (monomer)1.7 g powder (polymer);
- impact resistance: 8.3 kJ/m²;
- bending strength: 79 MPa;
- modulus of elasticity in bending: 2316 MPa;
- water sorption: 23.2 µg/mm³;
- Solubility: 1.8 µg/mm³
Packaging:
- 1000g
FuturaGen for pouring method polymer 1000g
Acrylic for pouring and cold methods, with very low shrinkage - 2%.
Application:
- complete dentures;
- partial dentures;
- repairs and relining.
Characteristics:
- high gloss and exceptionally smooth surface;
- good fit;
- short processing time.
Packaging:
- 1kg
Villacryl Bond 10ml
Villacryl Bond is a liquid preparation that improves the adhesion of acrylic teeth to the acrylic denture plate.
It is recommended for full and partial dentures made using the pouring technique.
It can also be used in traditional plaster pouring techniques as well as in silicone pouches.
Advantages:
- increases the adhesion between the denture plate and acrylic teeth;
- easy and convenient to use;
- can be used for all types of acrylic teeth.
How to use:
- bond intended for application to the previously matted mucosal part of acrylic teeth;
- After the wax has been boiled, the mold with the acrylic teeth should be dried using compressed air;
- apply the liquid with a brush;
- wait about 30 seconds for the preparation to evaporate;
- After evaporation, you can start working.
Packaging:
- 10ml
Isolate film 1000ml
Heat-resistant insulating agent based on alginate.
Advantages:
- creates a thin layer;
- gives smooth and non-porous surfaces;
- suitable for insulating plaster-plastic, plaster-plaster, plaster-silicone.
Packaging:
- 1000ml
Polymax 1 polymerizer DREVE 120 °C
Polymax 1 120°C ideal for repairs, relining and making dentures using the pouring method.
Advantages:
- precisely controlled temperature for cold and hot polymerization;
- temperature range up to 120 degrees;
- 90 minute timer;
- automatic safety sealing system;
- the center is made of specially coated aluminum;
- The device has protection against opening the cover when it is turned off.
Technical data:
- dimensions (height x width x depth) 230 x 290 x 300 mm;
- input power 450 W;
- frequency 50-60 Hz;
- pressure 3-4.2 bar (variable);
- pressure pot diameter 160 mm;
- pressure pot depth 110 mm;
- pressure pot capacity 2.2 l;
- weight 10.2 kg;
- temperature range up to 120° C.
Scope of delivery:
- Polymax including pressure hose and water drain hose
Castdon can for pouring method
Drip method container with transparent top, steel bottom plate with integrated chambers for removing wax from teeth.
The set includes a device for piercing channels, Ø 8 mm.
Packaging:
- 1 pc. can
- 1pc. Channel cutting tool Ø 8mm
Siliform silicone 2x850 ml
Silicone for pouring technique.
Used for embedding dentures in the Castdon technique;
Final hardness 14 Shore;
Dosage 1:1.
Packaging:
- 1 base 850ml + 1 catalyst 850ml
Instrument for cutting channels in agar and silicone Ø 8mm
An instrument for cutting out pouring channels in agar and silicone when making prostheses using the pouring method.
Packaging:
- 1pc.
Polymax 5 polymerizer DREVE 95°C
Dreve Polymax 5 pressure polymerizer.
A modern polymerizer guaranteeing high quality of prosthetic work.
Thanks to its high pressure and temperature stabilization, the polymerizer is perfect for making prostheses using the pouring method.
The large volume of the pressure pot also allows for the placement of large articulators, three brass cans with frames or four Castdon cans.
Characteristics:
- steplessly adjustable temperature for cold and hot polymerization;
- 90 minute timer;
- automatic safety sealing system;
- pressure pot made of specially coated aluminum;
- maintenance-free technology;
- very spacious chamber - possibility of placing the entire articulator.
Technical data:
- external dimensions: 34.5 x 38.5 x 31.0 cm;
- voltage: 230 V, 50/60 Hz;
- power:900 W;
- adjustable pressure from 3 to 6 bar;
- reaches temperatures up to 95 °C.
Scope of delivery:
- Polymax including pressure hose and water drain hose.
Packaging:
- 1 pc.
Polymax 3 polymerizer DREVE 95°C
Dreve Polymax 3 pressure polymerizer.
A modern polymerizer guaranteeing high quality of prosthetic work.
Thanks to its high pressure and temperature stabilization, the polymerizer is perfect for making prostheses using the pouring method.
It is optimally suited for finishing dentures.
Holds three brass tins including the frame or up to six Castdon tins for the pour method!
Characteristics:
- steplessly adjustable temperature for cold and hot polymerization;
- 90 minute timer;
- automatic safety sealing system;
- pressure pot made of specially coated aluminum.
Technical data:
- external dimensions: 29.5 x 31.5 x 44.0 cm;
- voltage: 230 V, 50/60 Hz;
- power: 900 W;
- adjustable pressure from 2 to 5 bar;
- reaches temperatures up to 95 °C.
Scope of delivery:
- Polymax including pressure hose and water drain hose.
Packaging:
- 1 pc.
Castdon powder pink opaque 750g
Acrylic for the pouring method based on polymethyl methacrylate copolymer.
- color pink opaque.
Properties:
- casting phase: 2-3 min;
- mixing ratio: 10 : 7 (polymer/monomer);
- Vickers hardness: > 135 MPa;
- bending strength > 60 MPa;
- modulus of elasticity in bending: > 1500 MPa;
- residual monomer value: < 4.5%;
- water absorption: < 32 μg/mm³ ;
- solubility in water: < 8 μg/mm³.
Packaging:
- 750g
Castdon powder pink transparent 750g
Acrylic for the pouring method based on polymethyl methacrylate copolymer.
- Color pink transparent.
Properties:
- casting phase: 2-3 min;
- mixing ratio: 10 : 7 (polymer/monomer);
- Vickers hardness: > 135 MPa;
- bending strength > 60 MPa;
- modulus of elasticity in bending: > 1500 MPa ;
- residual monomer value: < 4.5%;
- water absorption: < 32 μg/mm³ ;
- solubility in water: < 8 μg/mm³.
Packaging:
- 750g
Dreve Castdon Starter Kit (pink-transparent)
Castadon starter kit.
Starter kit for making 12 prostheses using the pouring method.
Set composition:
- Toothbrush strainer box;
- Castadon liquid 0.5l;
- Castadon powder 0.750g pink transparent with veins;
- Sprue cutter;
- Isolate film 1 l;
- Silicone Siliform 2 x 1 kg 1:1;
- Measuring cup for powder and liquid.
Packaging:
- 1 set
Castdon acrylic dispensers
Acrylic dispensers for the pouring method.
- Ensures optimal mixing proportions.
Packaging:
- set of 2pcs
Castdon Starter Kit (pink-opaque)
Castadon starter kit.
Starter kit for making 12 prostheses using the pouring method.
Set composition:
- Toothbrush strainer box;
- Castadon liquid 0.5l;
- Castadon powder 0.750g color pink-opaque;
- Sprue cutter;
- Isolate film 1 l;
- Silicone Siliform 2 x 1 kg 1:1;
- Measuring cup for powder and liquid.
Vertex Castavaria color 10 polymer 4000g
Vertex Castavaria pressure-curing acrylic for the production of full and partial dentures using the pouring technique.
Characteristics:
- color 10 pink transparent with veins;
- minimized shrinkage;
- color stability;
- extended liquid phase.
Application:
- complete dentures;
- skeletal prostheses.
Technical data:
- dough phase: 8 <…> 9 minutes;
- working time: 13 minutes;
- curing time: 30 minutes at 55°C and 2.5 bar pressure;
- mixing ratio by volume/parts by weight: 1 ml / 0.95 g liquid (monomer)1.7 g powder (polymer);
- impact resistance: 8.3 kJ/m²;
- bending strength: 79 MPa;
- modulus of elasticity in bending: 2316 MPa;
- water sorption: 23.2 µg/mm³;
- Solubility: 1.8 µg/mm³
Packaging:
- 4000g
Vertex Castavaria monomer 1000 ml
Vertex Castavaria acrylic fluid for the pouring technique.
Packaging:
- 1000ml
Dreve Agar Gelon colorless 6kg
High-quality gel for duplicating models.
Particularly hard and form-stable.
Specially developed for model casting and prosthetic casting techniques.
Fast and precise work thanks to low shrinkage and short curing times.
Packaging:
- 6kg
Polymax 1 DREVE polymerizer 95°C
Dreve Polymax 1 pressure polymerizer.
A modern polymerizer guaranteeing high quality of prosthetic work.
Thanks to its high pressure and temperature stabilization, the polymerizer is perfect for making prostheses using the pouring method.
Characteristics:
- Steplessly adjustable temperature for cold and hot polymerization;
- 90 minute timer;
- Automatic safety sealing system;
- Pressure pot made of specially coated aluminum;
- Maintenance-free technology;
Technical data:
- Dimensions (H x W x D) 230 x 290 x 300 mm;
- Input power 450 W;
- Frequency 50-60 Hz;
- Pressure 3-5.2 bar (variable);
- Pressure pot diameter 160 mm;
- Pressure pot depth 110 mm;
- Pressure pot capacity 2.2 l;
- Weight 10.2 kg;
Temperature range up to 95° C.
Scope of delivery:
Polymax including pressure hose and water drain hose.
Packaging:
- 1 pc.
FuturaGen Com4 polymer color pink 1000g NEW
Cold curing acrylic, perfect for the pouring method.
Application:
- complete dentures;
- partial restorations;
- denture repairs;
- relining of dentures.
Characteristics:
- minimal residual monomer content, which increases safety of use;
- high mechanical strength, making it also suitable for making occlusal splints;
- very good adaptation thanks to reduced polymerization shrinkage, which is especially important when working on implants;
- smooth surface reduces plaque build-up;
- color pink.
Packaging:
- 1kg
Vertex Castavaria 4000g + 2x1000ml set
Vertex Castavaria pressure-curing acrylic for the production of full and partial dentures using the pouring technique.
Characteristics:
- Minimized shrinkage.
- Color stability.
- Extended fluid phase.
Application:
- Complete dentures.
- Skeletal prostheses.
Packaging:
- 4000 g powder color 10
- 2x1000ml liquid