Kromptypo 4. Class IV extra hard prosthetic plaster with chromatic setting phase indicator for making models with high compressive and abrasion resistance.

Characteristics:

• Final color: pastel yellow.
• Water to powder ratio: 22ml/100g.
• Absorption time: 20 seconds.
• Mixing time (manual): 60 seconds.
• Mixing time (mechanical): 30 seconds.
• Pouring time: 3 minutes.
• Setting time: 7 minutes.
• Separation time after setting: 25-30 minutes.
• Expansion setting (after 2 hours): 0.08%
• Compressive strength (after 24 hours): 81 MPa, 11,740 psi, 828 kg/cm2.
• Rockwell hardness (after 24 hours): 85 HRL.

Packaging:

• 5kg

Stodent III Ortho is a type 3 hard orthodontic plaster recommended for archival, diagnostic and working models for the production of removable orthodontic appliances.

Description:

• Glossy white color.
• Small expansion.

Advantages:

• Smooth surface.
• Easy to prepare and process.
• Surface abrasion resistance.

Technical data:

• Mixing ratio approx. 28-30 ml / 100 g.
• Mixing time (vacuum) 30 s.
• Mixing time (manual) 60 – 90 sec.
• Setting time 10 -14 min.
• Impression release time 45 min.
• Compressive strength (after 1h ) 25 ± 2 MPa [> 20 MPa]
• Linear expansion (after 2h ) max. 0.15% [< 0.20 %]

Packaging:

• bag 25 kg

Description:

• Stodent III is a type 3 hard plaster recommended for antagonistic models and working models for the fabrication of removable and skeletal dentures.
• Light green color enriched with mango aroma
• A little expansion
• Good mechanical properties

Advantages:

• Smooth surface
• Simplified modeling due to high thixotropy
• High fracture resistance during release from the impression

Technical data:

• The mixing ratio is 30 ml / 100 g
• Stirring time (vacuum) 30 s
• Mixing time (manual) 60 - 90 s
• Setting time 10-14 min.
• Time to release from the impression 45 min.
• Compressive strength (after 1h ) 25 ± 2 MPa [> 20 MPa]
• Linear expansion (after 2h ) max. 0.15% [<0.20 %]

Packaging:

• 3 kg.

Stodent IV is a super-hard type 4 dental plaster recommended for making working models of fixed skeletal dentures and flexible dentures, combined works, post-implantation dentures.

Description:

• Vanilla cream color.
• Small expansion.
• Good fluidity.

Advantages:

• Very good reproduction of details.
• Smooth surface.
• High resistance to mechanical damage.

Technical data:

• Mixing ratio 20 ml / 100 g
• Mixing time (vacuum) 30 s
• Mixing time (manual) 60 – 90 sec
• Setting time 8 -12 min.
• Compressive strength (after 1h ) 45 ± 2 MPa [> 35 MPa]
• Linear expansion (after 2h ) max. 0.10% [< 0.15 %]
• Linear expansion after 24h < 0.18* %

Packaging:

• 3kg

Stodent IV is a super-hard type 4 dental plaster recommended for making working models of fixed skeletal dentures and flexible dentures, combined works, post-implantation prostheses.

Description:

• Gray color with a strawberry scent.
• Small expansion.
• Good fluidity.

Advantages:

• Very good reproduction of details.
• Smooth surface.
• High resistance to mechanical damage.

Technical data:

• Mixing ratio 20 ml / 100 g
• Mixing time (vacuum) 30 s
• Mixing time (manual) 60 – 90 sec
• Setting time 8 -12 min.
• Compressive strength (after 1h ) 45 ± 2 MPa [> 35 MPa]
• Linear expansion (after 2h ) max. 0.10% [< 0.15 %]
• Linear expansion after 24h < 0.18* %

Packaging:

• 3kg

Stodent III is a type 3 hard plaster recommended for antagonist models and working models in the manufacture of removable and skeletal dentures.

Description:

• Available in: yellow
• Small expansion
• Good mechanical properties

Benefits:

• Smooth surface
• Facilitated model making due to high thixotropy
• High breakage resistance during release from the impression

Technical data:

• Mixing ratio 30 ml / 100 g
• Mixing time (vacuum) 30 s
• Mixing time (manual) 60 – 90 sec
• Setting time 10 -14 min.
• Impression release time 45 min.
• Compressive strength (after 1h ) 25 ± 2 MPa [> 20 MPa]
• Linear expansion (after 2h ) max. 0.15% [< 0.20 %]

Packaging:

• 25 kg

Stodent II is a type 2 model gypsum recommended for filling the boxes when making removable dentures with hot polymerizing acrylic materials and for other auxiliary works.

Benefits:

• Optimal reproduction of details
• Optimum fluidity
• White color
• Easy to mix
• Ease of processing
• Ease of releasing the finished denture from the can

Technical data:

• Mixing ratio 50 ml / 100 g
• Mixing time (vacuum) 30 s
• Mixing time (manual) 60 - 90 s
• Setting time 14-18 min.
• Impression release time 45 min.
• Compressive strength (after 1h ) 11 ± 2 MPa [> 9 MPa]
• Linear expansion (after 2h ) max. 0.25% [<0.30 %]

Packaging:

• bag 25 kg

GC Fujirock EP Premium Line Super Hard Plaster, Pastel Yellow - 11 kg

IV class plaster. For high-precision techniques such as implant work and complex all-ceramic work. Improved plaster composition and improved color setting. The ability to scan. Pastel yellow color

Physical data:

• setting time 9-12 min;
• post-set expansion <0.09%;
• compressive strength after 1 h approx. 60 N / mm².

Package:

11 kg

Gypsum, III class Eco Stone 5 kg. yellow Hard synthetic plaster, type 3, of high quality, intended for casting works with the technique of partial dentures, skeletal dentures and orthodontic appliances. Meets the requirements of ISO 6873-3. Certificate of Approval No. IL-5629 / MS.

Gypsum III class Eco Stone provides:

• obtaining models with high durability,
• minimum, uniform expansion coefficient,
• constant level of quality.

Physical properties :

• Hardening time: approx. 10 minutes.
• Compressive strength after 1 h: more than 20 N / sq. Mm.
• Hardness after 24 hours over 80 N / sq mm
• Linear expansion after 2 hours : less than 0.14%

Application method:

Mixing ratio

Gypsum 100 g: 30 ml Water: gypsum 0.3 ml / g Working temperature approx. 23 degrees. C Quickly in no more than 10 sec. pour gypsum to water in the above-mentioned proportions and wait 20 seconds. until the water is absorbed by the plaster. Mechanical mixing: 30 sec. Manual mixing: 60 sec.

During this time, the gypsum reaches the optimal consistency for pouring into model molds on a shaker. Shaking time: approx. 6 min. After this time, stop shaking so as not to disturb the course of crystallization.

Storage :

At least 12 months in a sealed, moisture-proof packaging.

Package:

5 kg.

Class IV plaster for the base of models, perfectly flowing, dark blue.

Advantages:

• very fluid consistency
• does not require work with a vibrating table
• no air bubbles between pins
• low expansion
• absolutely smooth surface
• high final hardness
• big time saving

Physical properties:

• Setting time 10-12 min.
• Dry compressive strength 70 Mpa

- linear expansion:

after 2 hours 0.06%

Preparation:

gypsum / distilled water: 100 g / 23 ml working temperature 23 ° C

Package 5 kg

GC Fujirock EP - type IV super hard plaster. Very break-resistant, fluid. Stable at the edges, long processing time, short binding.

Features:

• Processing time 8min.
• Expansion after setting after 2h 0.08%.
• Compressive strength after 1 h 53 Mpa, after 24 h 80 Mpa.
• Final hardness 310 N / mm2.

Attention:

Due to the high weight of the goods (15 kg), an additional fee will be added to the shipment.

GC Fujirock EP Premium Line Super Hard Plaster, Polar White - 4 kg

IV class plaster. For high-precision techniques such as implant work and complex all-ceramic work. Improved powder composition and improved color setting. The ability to scan. Color: polar white

Physical data:

• setting time 9-12 min;
• post-set expansion <0.09%;
• compressive strength after 1 h approx. 60 N / mm².

Package:

4 kg

Gypsum IV class Eco Stone Natural Premium super hard gypsum recommended for posts and split models.

Advantages:

• High stability
• Very smooth surface
• Scratch-resistant
• They show high precision

Technical data :

• Water to plaster ratio: 22/100
• Setting time: 12-14 minutes
• Linear expansion after 2 h below 0.09%
• Gold-brown color

Package:

• 5 kg

Articulation plaster, quick-setting for fixing models in articulators with very good stability with minimal expansion.

Characteristic:

• Articulation plaster, white color.

Parameters:

• Mixing ratio: 30 ml / 100 g
• Working time: 90 sec.
• Setting time: 3 min
• Expansion after setting: 0.01%
• Compressive strength 1h: 25 Mpa

Package:

• 10 kg. (5x2kg)

Gypsum class IV for working models for the performance of permanent dentures, combined work, post-implantation dentures, etc. Sand color.

Parameters:

• Water / Powder 20 ml / 100 g
• Mixing time (manually) - 1:00 min
• Mixing time (vacuum) - 00:30 sec
• Working time 12 min
• Setting time 14 min
• Release time 45 min
• Expansion after 2 h 0.08%
• Expansion after 48 h 0.19%
• Compressive strength 1h 52 MPa (530 kg / cm2)
• Compressive strength 48 h 81 MPa (826 kg / cm2)

Package:

3 kg.

GC Fujirock EP is a class 4 plaster of the highest quality. Designed to perform any prosthetic work, with the highest precision, with exceptional hardness and resistance to deformation.

Package:

5 kg.

Gypsum IV class. For high-precision implant work and complex all-ceramic work. Improved plaster composition and improved color setting. The ability to scan.

Physical data:

• setting time 9-12 min;
• expansion after setting after 2 h approx. 0.09%;
• compressive strength after 1 h approx. 60 N / mm2.
• grey colour

Package:

4 kg

Eco Stone Blue color Hard synthetic plaster, type 3, of high quality, intended for casting works with the technique of partial dentures, skeletal dentures and orthodontic appliances. Meets the requirements of ISO 6873-3. Certificate of Approval No. IL-5629 / MS.

Eco Stone provides:

• obtaining models with high durability,
• minimum, uniform expansion coefficient,
• constant level of quality.

Physical properties :

Hardening time: approx. 10-12 minutes. Compressive strength after 1 h: over 20 N / mm kw. Hardness after 24 h over 80 N / mm kw. Linear expansion after 2 h. : less than 0.14%

Application method:

Mixing ratio

Eco Stone: water 100 g: 30 ml Water: gypsum 0.3 ml / g Working temperature approx. 23 degrees. C Quickly in no more than 10 sec. pour gypsum to water in the above-mentioned proportions and wait 20 seconds. until the water is absorbed by the plaster. Mechanical mixing: 30 sec. Manual mixing: 60 sec. During this time, the gypsum reaches the optimal consistency for pouring into model molds on a shaker. Shaking time: approx. 6 min. After this time, stop shaking so as not to disturb the course of crystallization.

Storage :

At least 12 months in a sealed, moisture-proof packaging.

Package:

5 kg.

Universal grade II plaster.

Technical data : Mixing ratio: 50ml / 100g. Working time: 6min. Setting time: 10-12 minutes. Linear expansion after 2h: 0.15%.

Packaging 5 kg.

Stodent III is a type 3 hard plaster recommended for antagonistic models and working models for the fabrication of removable and skeletal dentures.

Description:

• Available in color: yellow
• A little expansion
• Good mechanical properties

Advantages:

• Smooth surface
• Facilitated model making due to high thixotropicity
• High fracture resistance when released from the impression

Technical data:

• The mixing ratio is 30 ml / 100 g
• Stirring time (vacuum) 30 s
• Mixing time (manual) 60 - 90 s
• Setting time 10-14 min.
• Time to release from the impression 45 min.
• Compressive strength (after 1h ) 25 ± 2 MPa [> 20 MPa]
• Linear expansion (after 2h ) max. 0.15% [<0.20 %]

Package:

• 5 kg

Characteristic:

Special double expansion plaster for duplicating models, white color. It does not require the use of a special liquid, mixed with demineralized water. Dedicated to work with devices that inject thermoplastic materials.

Package:

3 kg bucket

Kimberlite gold brown color. High-quality model gypsum of natural origin.

Benefits:

• Releases the impression accurately and easily (only 20 minutes!)
• Thixotropic
• Very high durability
• It allows to obtain perfect results when working with optical scanning systems

Instructions for use:

• Powder / water ratio: 100 g / 20 ml
• Working temperature: 20-23 ° C
• Mechanical mixing under vacuum: 30 seconds
• Manual mixing: 60 seconds

Physical properties:

• Working time: 7 min
• Start of hardening: 9 min
• End of hardening: 13 min
• Expansion (2 hours): 0.08%
• Hardness (24 hours): 247 N / mm2
• Crushing strength (1g): 58 N / mm2

Package:

• 2Kg

Diamant. Color gold. High-quality synthetic gypsum. Ideal for all types of fixed dentures, stumps and master models.

Benefits:

• Releases the impression thoroughly and easily (only 20 minutes!)
• Thixotropic
• Very high durability
• It allows you to obtain excellent results when working with optical scanning systems

Instructions for use:

• Powder / water ratio: 100 g / 20 ml
• Working temperature: 20-23 ° C
• Mechanical mixing under vacuum: 30 seconds
• Manual mixing: 60 seconds

Physical properties:

• Working time: 8 min
• Start of hardening: 11 min
• End of hardening: 15 minutes
• Expansion (2 hours): 0.08%
• Hardness (24 hours): 247 N / mm2
• Crushing strength (1g): 60 N / mm2

Packaging: -2 kg

Material based on polyurethane for the production of accurate models. Very good and stable dimensional reproduction. After an hour, the material is so hard that it can be processed and sanded. The set is sufficient for approximately 10 complete base bends.

Package:

• 2x100ml Base
• 1x100ml hardener
• 1x400g filler
• Accessories

Class IV plaster for super hard Rubinite models, pink, natural color. Perfect for frame work and thermal injection techniques.

Properties:

• Mixing ratio: 22-24 ml / 100 g
• Working time: 7 min.
• Setting time: 12 minutes
• Expansion after setting: 0.10%
• Compressive strength: 40 Mpa

Package:

• 5 kg.

Grade IV plaster on the base of red color.

Properties:

• consistency: 24 ml / 100 g
• working time: 6 min.
• setting time: 11 min
• expansion after setting: 0.05%
• compressive strength (1h): 40 Mpa

Package:

2 kg

Class IV plaster for the base of models, perfectly flowing, orange.

Advantages:

• very fluid consistency
• does not require work with a vibrating table
• no air bubbles between pins
• low expansion
• absolutely smooth surface
• high final hardness
• big time saving

Physical properties:

• Setting time 10-12 min.
• Dry compressive strength 70 Mpa

- linear expansion:

* after 2 hours 0.06%

Preparation:

gypsum / distilled water: 100 g / 23 ml working temperature 23 ° C

Package:

5 kg

Characteristic:

Gypsum IV class Eco Stone Ortho 5kg Premium super white enriched with synthetic material.

It is very well suited for diagnostic, demonstration, orthodontic and porcelain models.

Parameters:

• Hand mixing time - 60 sec.
• Time of mixing in the mixer - 30 sec.
• Setting time - 10-12 minutes
• 2h expansion - 0.14%
• Water to plaster ratio 26-27 ml: 100 g

Package:

25 kg

Elite Master is a working model plaster for fixed dentures with resin particles, for chipping-free chamfering.

Characteristic:

• Low expansion, even after 48 hours

• Accuracy of mapping details

• It does not contain formaldehyde

• Resistant to spraying

Advantages:

• Chamfering without chipping, thanks to the high resistance obtained thanks to the resin particles contained in the plaster

• Thixotropy to facilitate model casting

Parameters:

• Color Soft Gray - light gray
• Water / Powder 21 ml / 100 g
• Mixing time (by hand) - 1:00 min
• Mixing time (vacuum mixer) - 00:30 min
• Working time 12:00 min
• Vicat setting time - 14:00 min
• Release time 45:00 min
• Expansion after 2 h 0.08%
• Expansion after 48 h 0.19%
• Compressive strength 1h 50 MPa (510 kg / cm2)
• Compressive strength 48 h 75 MPa (765 kg / cm2)

Package:

3 kg.

A combination of high-quality plastic and grade IV plaster, super-hard, ideal for prosthetic work on implants.

Description:

• Working time 7 minutes
• Start of hardening 8 min
• End of hardening 10 minutes
• Total hardening time 30 min
• Expansion (2h): 0.10%
• Compressive strength (1 h): 50 MP
• The ratio of powder to water 100g / 20ml
• Working temperature 20-23 degrees ° C
• Mechanical and vacuum mixing 30 sec

Package:

• 2 kg

Expansion plaster EXPANDER - for making working models using the injection technology of thermoplastics - effectively compensates for plastic shrinkage after injection - ensures the best possible adjustment of thermoplastic dentures to the prosthetic field

Weight:

• 3 kg

Type V super hard dental plaster, golden brown color.

Destiny:

• Working models for the performance of permanent dentures, combined work, post-implantation dentures.

Features:

• High resistance to mechanical damage.
• Very good dimensional stability.
• Accurate reproduction of details.

Parameters:

• Color golden brown
• The mixing ratio is 20 ml / 100 g
• Working time 7 minutes

• Setting time (at 23 ° C) 12-14 min

• Linear expansion after 2h 0.25%

Package:

• 5 kg

SPECIAL OFFER;

• Buy 5 pieces (you can freely mix the color) and you will pay for 4 pieces.

Gip IV class Hinristone Saphir.

Extremely durable, hard plaster with a "snap-set" effect that allows you to remove the stump and work on it after just 30 minutes.

Characteristic:

• Creamy but very flowing texture
• High trixotropic index
• Low expansion
• Excellent CAD/CAM scanning properties
• Homogeneous and delamination-free structure

Technical data:

• Water to plaster ratio: 20:100
• Working time 6-7 minutes
• Setting time 12-14 min
• Binding expansion 0.08% after 2h
• Compressive strength, dry 90 MPa

Colors:

• golden brown
• Grey.
• ivory.
• Maize Yellow.

Packaging:

• 5kg.

A combination of high-quality plastic and grade IV plaster, super-hard, ideal for prosthetic work on implants. Peach colour.

Technical data:

• Working time 7 minutes
• Start of hardening 8 min
• End of hardening 10 minutes
• Total hardening time 30 min
• Expansion (2h): 0.10%
• Compressive strength (1 h): 50 MP
• powder to water ratio 100g / 20ml
• working temperature 20-23 degrees C
• mechanical and vacuum mixing 30 sec

Package:

• 2 kg

Stodent III is a type 3 hard plaster recommended for antagonist models and working models in the manufacture of removable and skeletal dentures.

Description:

• Available in: blue
• Small expansion
• Good mechanical properties

Benefits:

• Smooth surface
• Facilitated model making due to high thixotropy
• High breakage resistance during release from the impression

Technical data:

• Mixing ratio 30 ml / 100 g
• Mixing time (vacuum) 30 s
• Mixing time (manual) 60 – 90 sec
• Setting time 10 -14 min.
• Impression release time 45 min.
• Compressive strength (after 1h ) 25 ± 2 MPa [> 20 MPa]
• Linear expansion (after 2h ) max. 0.15% [< 0.20 %]

Packaging:

• 25 kg

GC Fujirock EP Premium Line Super Hard Plaster, Pastel Yellow - 4kg

IV class plaster. For high-precision techniques such as implant work and complex all-ceramic work. Improved plaster composition and improved color setting. The ability to scan. Pastel yellow color

Physical data:

• setting time 9-12 min;
• post-set expansion <0.09%;
• compressive strength after 1 h approx. 60 N / mm².

Package:

4 kg

Grade IV plaster on the base of terra color.

Properties:

• consistency: 24 ml / 100 g
• working time: 6 min.
• setting time: 11 min
• expansion after setting: 0.05%
• compressive strength (1h): 40 Mpa

Package:

2 kg

Stodent II is a model gypsum type 2 recommended for filling cans when making removable dentures with hot-curing acrylic plastics and for other auxiliary works.

Description:

• Optimal reproduction of details
• Optimal fluidity
• White color

Advantages:

• Ease of mixing
• Ease of processing
• Ease of releasing the finished can from the denture

Technical data:

• The mixing ratio is 50 ml / 100 g
• Stirring time (vacuum) 30 s
• Mixing time (manual) 60 - 90 s
• Setting time 14-18 minutes.
• Release time from the impression 45 min.
• Compressive strength (after 1h ) 11 ± 2 MPa [> 9 MPa]
• Linear expansion (after 2h ) max. 0.25% [<0.30 %]

Package:

• 5 kg

Plaster for working models in the production of removable orthodontic appliances.

Characteristic:

• Low degree of linear expansion

• Shiny white color

• High liquidity

Advantages:

• Smooth surface

• Easy to prepare and process

• Surface resistance to abrasion

Parameters:

• White color
• The mixing ratio is 30 ml / 100 g
• Setting time 10 - 12 min
• Linear expansion after 2h <0.13%

Package:

6kg

Stodent III is a type 3 hard plaster recommended for antagonistic models and working models for the fabrication of removable and skeletal dentures.

Description:

• Available in color: blue
• A little expansion
• Good mechanical properties

Advantages:

• Smooth surface
• Facilitated model making due to high thixotropicity
• High fracture resistance when released from the impression

Technical data:

• The mixing ratio is 30 ml / 100 g
• Stirring time (vacuum) 30 s
• Mixing time (manual) 60 - 90 s
• Setting time 10-14 min.
• Time to release from the impression 45 min.
• Compressive strength (after 1h ) 25 ± 2 MPa [> 20 MPa]
• Linear expansion (after 2h ) max. 0.15% [<0.20 %]

Package:

• 3 kg

Hinrizit E is a dental plaster with a special formula and high bond expansion. This special gypsum is used for the production of models and for canning plastic prostheses, due to its high bond expansion, it compensates for the contraction of plastics from which the prostheses are made (eg SR Ivocap Injection System, Acetal, Deflex, FJP, Valplast). Hinrizit E can be used with all plastics for the production of dentures.

Application:

• Technique of producing plastic dentures

Properties:

• White color

• Water: gypsum ratio - 25: 100

• Mixing time in min. - 5-6

• Hardening time in min. - 10-12

• Expansion in the bonding process - 0.60

• Compressive strength after 1 hour. - 30 MPa

• Dry compression strength - 60 MPa

Package:

• 5 kg.

Super-hard plaster with excellent fluidity for making the bases of models without the use of a vibrator. Initial consistency becomes more fluid with increasing mixing time, and it flows optimally during pouring.

Application:

• bases of the dental arches in split models. -all pin systems using plaster.

Parameters:

• White color
• water-gypsum ratio 23: 100
• mixing time in min. 5-6
• hardening time in min. 10-12
• expansion in the binding process 0.06
• compressive strength 50 MPa after 1 hour
• dry compression resistance 70 MPa

Package:

• 5 kg.

Universal grade II plaster.

• Mixing ratio: 50ml / 100g.
• Working time: 6min.
• Setting time: 10-12 minutes.
• Linear expansion after 2 h: 015%.

Package:

• 25kg

Eco Stone 3rd class gypsum 25kg yellow Hard synthetic gypsum type 3 in yellow, high quality, intended for casting works in the technique of partial settling dentures, frame and orthodontic appliances. It meets the requirements of the ISO 6873-3 standard. Certificate of Admission No. IL-5629/MS.

Eco Stone III class gypsum provides:

• obtaining models with high durability,
• minimum, uniform coefficient of expansion,
• a constant level of quality.

Physical properties:

• Hardening time: approx. 10 min.
• Compressive strength after 1 h: more than 20 N/mm sq.
• Hardness after 24 hours over 80 N/sq
• Linear expansion after 2 hours : below 0.14%

Mixing ratio:

• Water 100g : 30ml
• Water: gypsum 0.3 ml/g
• Operating temperature approx. 23 degrees. c

How to use:

• Fast in no more than 10 seconds. pour gypsum into water in the proportions given above and wait 20 seconds. until the water is absorbed by the gypsum.
• Mechanical mixing : 30 sec.
• Manual mixing: 60 sec.

During this time, the gypsum reaches the optimum consistency for pouring into model molds on a shaker. Shaking time: approx. 6 min

After this time, stop shaking so as not to disturb the crystallization process.

Storage :

At least 12 months in sealed, moisture-proof packaging.

Packaging:

• 25kg.

Gypsum class III Eco Stone 25 kg blue.

Hard, blue type 3 synthetic gypsum of high quality, intended for casting works in the technique of partial settling dentures, skeletal and orthodontic appliances. Meets the requirements of ISO 6873-3.

Eco Stone III class provides:

• obtaining models with high durability,
• minimum, uniform coefficient of expansion,
• a constant level of quality.

Physical properties:

• Hardening time: approx. 10-12 min.
• Compressive strength after 1 h: more than 20 N/mm sq.
• Hardness after 24 hours over 80 N/sq
• Linear expansion after 2 hours : below 0.14%

Mixing ratio:

• GILUDUR : water 100 g : 30 ml
• Water: gypsum 0.3 ml/g
• Operating temperature approx. 23 degrees. c

How to use:

• Fast in no more than 10 seconds. pour gypsum into water in the proportions given above and wait 20 seconds. until the water is absorbed by the gypsum.

Mechanical mixing : 30 sec. Manual mixing: 60 sec.

During this time, the gypsum reaches the optimum consistency for pouring into model molds on a shaker. Shaking time: approx. 6 min

After this time, stop shaking so as not to disturb the crystallization process.

Storage :

At least 12 months in sealed, moisture-proof packaging.

Packaging:

• 25kg.

Attention:

Due to the high weight of the goods (25 kg), an additional fee will be added to the shipment.

Eco Stone Natural Premium class IV gypsum super hard gypsum recommended for posts and split models.

Benefits:

• High stability
• Very smooth surface
• Scratch resistant
• They show high precision

Technical data :

• Water to plaster ratio: 22/100
• Setting time: 12-14 min
• Linear expansion after 2 hours less than 0.09%
• Color golden-brown

Attention:

Due to the high weight of the goods (25 kg), an additional fee will be added to the shipment.

Packaging:

• 25 kg

Class IV gypsum for model bases, perfectly flowing, dark blue.

Benefits:

• very fluid consistency
• does not require work with a vibrating table
• no air bubbles between the pins
• low expansion
• absolutely smooth surface
• high final hardness
• big time saving

Physical properties:

• Setting time 10-12 min.
• Dry compressive strength 70 MPa

- linear expansion:

• after 2 hours 0.06%

Preparation:

• gypsum / distilled water: 100g / 23 ml
• operating temperature 23 °C

Attention:

• Due to the high weight of the goods (25 kg), an additional fee will be added to the shipment.

Packaging:

• 25 kg

Plaster for working models when making removable orthodontic appliances.

Characteristic:

• Low degree of linear expansion

• Glossy white color

• High liquidity

Benefits:

• Smooth surface

• Easy to prepare and process

• Surface abrasion resistance

parameters:

• White color
• Mixing ratio 30 ml / 100 g
• Setting time 10 - 12 min
• Linear expansion after 2h < 0.13%

Attention:

• Due to the high weight of the goods (25 kg), an additional fee will be added to the shipment.

Packaging:

• 25 kg.

Characteristic:

Gypsum class IV Eco Stone Ortho 25kg Premium super white enriched with synthetic material.

It is very well suited for diagnostic models, demonstration models, for orthodontics and under porcelain.

parameters:

• Manual mixing time - 60 sec.
• Mixing time in the mixer - 30 sec.
• Setting time - 10 -12 minutes
• Expansion after 2 hours - 0.14%

Packaging:

• 25 kg.

Super hard dental plaster type V, gold-brown color.

Destiny:

• Working models for making permanent prostheses, combined works, post-implantation prostheses.

Characteristics:

• High resistance to mechanical damage.
• Very good dimensional stability.
• Accurate reproduction of details.

parameters:

• Golden-brown color
• Mixing ratio 20 ml / 100 g
• Working time 7 min

• Setting time (at 23°C) 12-14 min

• Linear expansion after 2h 0.25%

Attention:

• Due to the high weight of the goods (25 kg), an additional fee will be added to the shipment.

Packaging:

• 25 kg