Aurofilm spray 100 ml
Aurofilm spray is a surface tension reducing agent. A reliable preparation agent, eliminates the hydrophobic effect, thus contributing to the creation of smooth casting surfaces.
Characteristics:
- Always dry the surfaces after spraying.
- Wet areas can cause rough casting surfaces.
Packaging:
- 100ml spray.
Isocera 200 ml Plaster/wax isolator
Isocera isolating agent used in the modeling of crowns and bridges.
Characteristics:
- This agent insulates the wax very well from the plaster model.
- It works especially well when insulating posts, when wax caps are made in the immersion process.
Packaging:
- 200ml.
Wiropaint plus for smoothing models 200ml
Mass for smoothing modeled in wax skeletal dentures.
Characteristics:
- It makes it possible to obtain a very smooth surface of the casting and significantly reduces the time of post-processing.
- It does not form a sediment and comes in a form for direct use.
Packaging:
- 200ml.
Izolit SL insulating liquid 1kg of liquid
Isolit SL is a colloidal solution based on alginic acid salts, stabilized with a bactericidal agent and colored.
Used:
- Intended for insulating the surface of gypsum molds from methacrylate dough.
Usage:
- The plaster mold, made in a generally accepted manner, should be thoroughly rinsed with a stream of boiling water to completely remove the modeling wax from it. The ease of spreading the insulating liquid and its proper adhesion to the surface of the mold later depend on the good melting of the wax, therefore this operation should be given special attention. Then, pour IZOLIT SL liquid into a small container and, using a soft brush, coat the surface of the gypsum mold, previously brought to a temperature of approx. 40ºC. After a few minutes, it is advisable to reapply a layer of IZOLIT SL on the gypsum. After the insulating layer has dried, you can start forming the methacrylate dough.
Attention:
- The brush used to coat the gypsum mold should not be immersed directly in the bottle with IZOLITEM SL, because gypsum residues deposited on it may cause gelling of the liquid in the bottle. For the same reason, do not pour the rest of the liquid from the dish into the bottle.
The storage conditions:
- Contains bronopol. Keep locked up and out of reach of children.
Packaging:
- 1 kg of liquid
Separating Fluid 500ml
Separating Fluid exhibits exceptional separating properties and thus optimally insulates all denture base materials and ensures smooth surfaces.
- Insulation: plaster / acrylic, plaster / plaster.
Package:
- 500 ml.
Die Lube liquid 50g
Die lube pin insulator liquid. For isolating plaster, plastic and metal stumps from wax, porcelain and plastic.
Characteristics:
- It guarantees easy removal of caps shaped in wax.
- It is also used to smooth milled metal surfaces.
- Does not contain oil.
- Does not react with silicone.
Package:
- 50ml.
Wax-Fix 50ml
Wax-Fix adhesive for plastic wax stencils and retention beads.
Characteristics:
- Apply to wet or dry and hardened investment surfaces and plastic surfaces.
- Glued elements can be easily moved.
Packaging:
- 50ml.
He asked for degreasing silicone surfaces
Prosil preparation is intended for degreasing silicone surfaces.
Characteristics:
- Helps to achieve absolute model accuracy by facilitating the flow of plaster into the impression holes.
- Prevents the formation of air bubbles.
- It does not leave any additional layer.
Packaging:
- 100ml.
Gipssol gypsum solvent 110g
Gipssol is a preparation intended for removing gypsum residues after polymerization in gypsum molds from dentures, plastic crowns, etc. The expected effect is obtained after 2-3 hours. At higher concentrations, the preparation can be used to clean impression trays.
Characteristics:
- The preparation is used to remove plaster residues from dentures.
- The agent does not dissolve the insulating layer.
Packaging: - 110g.
Isofix 2000 gypsum-gypsum insulating liquid 2x1l
Isofix 2000, supplement. Izofix 2000 is a film-free gypsum-gypsum insulator for insulating gypsum layers in folded models.
Characteristics:
- It seals the gypsum surface without forming a film.
- It penetrates deep into the surface of the plaster model, clogging the pores and does not change the size of the model.
- The gypsum surface hardens and becomes smooth and non-absorbent.
Packaging:
- 2 x 1000 ml cans.
Vertex Divosep Blue 1000 ml
Vertex Divosep Blue.
- Preparation for isolating acrylic from plaster and plaster from plaster.
- Universally applicable to both cold and hot curing acrylics.
Packaging:
- 1000 ml
Unipurol to remove impurities
Unipurol is a concentrate for removing impurities after gypsum, cement, alginates, polishing pastes for degreasing and derusting surfaces.
Characteristics:
- Especially recommended for ultrasonic cleaners.
- The liquid does not affect the structure of metal, varnished and plastic surfaces.
- Does not expose to aggressive action in case of direct contact with the skin /pH 5/.
- Removal of plaster from dentures and interdental spaces as well as calculus from used dentures.
- Degreasing metal parts after polishing or before electropolishing.
- Cleaning trays and tools from alginate impression materials, gypsum and cement residues.
- Due to the degreasing effect of the liquid, cleaning of spoons and tools can be combined with pre-washing.
Packaging:
- 1l.
Profilm to eliminate the surface tension of wax 100ml
Profilm, the preparation is a liquid designed to eliminate the surface tension on the wax elements of skeletal dentures and the wax base of cast crowns and bridges.
Characteristics:
- It has degreasing and disinfecting properties.
- It can be used to clean the surface of tools from residues of fats, dyes, resins, waxes, varnishes and plastics.
Packaging:
- 100ml.
Picosilk 75ml
Picosilk preparation for wetting wax models before embedding in the investment mass. Pikosilk is an indispensable preparation in the foundry technique, as it allows for making a precise casting without unnecessary micro-feeds.
Renfert catalog number 15500000
Characteristics:
- Expanding the surface of the wax model: crowns, bridges, skeletal dentures.
- Improving the flow of the investment at the wax surface for a more accurate casting and easier release from the investment.
Usage:
- The wax model prepared for embedding in the investment mass should be sprayed with Picosilk from a distance of approx. 15 cm.
- Make sure the surface of the model is quite damp and let it dry for a while.
- Then place the model in the casting ring and pour investment compound.
Packaging:
- 75ml spray.
Separation 1000ml
Liquid separator for acrylic-gypsum and plaster-gypsum insulation. Preparation for technical and dental work. It is designed to isolate the surface of plaster molds from acrylic dough for dentures, crown veneers, crowns and other prosthetic works. Creates an appropriate thickness of the insulating membrane.
Characteristics:
- The pink separation is universally applicable.
- Slowly drying blue separator absorbed by gypsum, recommended in pressure techniques, holds well, does not come off.
Packaging:
- 1000 ml.
Proisol wax-gypsum insulator 100ml
The product prevents the wax from sticking to the plaster model. It is an insulation for wax during all work on plaster models.
Usage:
- After wetting the model, use an atomizer to spray the surface on which the wax elements will be made.
Advantages:
- Makes wax models very easy to remove.
- In addition, it cleans and maintains plastic surfaces.
- Prevents freezing and defrosts locks.
Packaging:
- 100ml.
Hartebad gypsum hardener 125ml
Hartebad - self-hardening preparation for covering the surface of plaster models. One-time (one-layer) application of the preparation on the gypsum surface causes its hardening and resistance to water. Hartebad does not create a film layer on the hardened surface and does not leave any deposits.
Renfert catalog number 17192000
Characteristics:
- Thanks to the properties of the Hartebad preparation, it is used for sealing the edges of crowns and inlays and onlays marked on a plaster model (e.g. with a pencil).
- Excellent effects are obtained by using the preparation during modeling of the cervical layer.
- Apply a single, thin layer with a small brush, e.g. size 1 to 4.
Packaging:
- 125ml can.
Dissol for dissolving plaster and alginate 1000g
Preparation for removing plaster and alginate residues. Dissol eliminates the need for mechanical removal of plaster and alginate residues.
Features:
- During the dissolution of the remnants, the preparation gradually becomes discolored.
- The fluid can be used many times until it loses color.
Package:
- 1000g.
Futura Sep Plus
Futura Sep Plus one-component, alginate-based insulation material for isolating plaster from plastics.
Package:
1l.
Picosep 30ml
Picosep is an excellent dual-purpose wax/plaster and porcelain/plaster insulator.
Renfert catalog number 15520030
- To insulate with Picosep, just apply a thin layer with a small brush to the surface of the plaster model.
- By applying Picosep only once, a micromembrane sufficient for complete isolation is obtained.
Characteristics:
- Insulation between the plaster stump and the wax cap in the so-called "maczaki".
- Insulation between the plaster model and porcelain, especially in the cervical and proximal areas.
- Apply once with a thin layer even when the edge of the crown is supplemented with a large amount of cervical wax.
Packaging:
- 30ml.
Erkoskin 50ml
Erkoskin is a self-curing material that forms a film layer on the plaster model.
Package:
- 1pc / 50ml.
Gipsolite 1 kg of liquid
Gipsolite - a preparation intended for the removal of plaster remains from dental prostheses and orthodontic appliances.
Benefits:
- Eliminates the need for mechanical removal of plaster residue.
Application:
- In order to remove plaster residues, the prosthesis should be placed in a liquid and left for about 24 hours.
- Wash the cleaned denture under running water and start working on and polishing.
** The storage conditions:**
- Keep locked up and out of the reach of children.
Package:
1 kg. fluid
Iso-sol 1L
A film-forming preparation is used to isolate acrylic from plaster. The preparation does not contain formaldehyde. It has a bacteriostatic effect. It enables easy separation of plaster molds after polymerization. It creates a very thin and smooth film which guarantees maximum fidelity. It can be used to isolate gypsum from acrylic resins and gypsum from gypsum.
Benefits:
- Very good adhesion to plaster
- High efficiency, a small amount of the preparation provides effective insulation
Package:
- 1000 ml.
Hinrisid 250 ml / Gipsil 250 ml
Hinrsid / Gipsil surfactant-based agent for silicone and polyether impressions before model casting. After applying the preparation, the models are smooth and free of air bubbles.
Package:
- 250 ml spray.
Hinrisol 250 ml / Neutrasil 250ml
Hinrisol / Neutrasil alcohol-based liquid for reducing the tension of silicone surfaces, before pouring the model out of the investment compound.
Not suitable for alginates, hydrocolloids and polyethers.
Package:
- 250 ml spray
Separating fluid 1000ml
Separating Fluid exhibits exceptional separating properties and thus optimally insulates all denture base materials and ensures smooth surfaces.
- Insulation: plaster / acrylic, plaster / plaster.
Package:
- 1000 ml.
GipEx liquid for dissolving gypsum 1L
Preparation for removing plaster and sediment residues from acrylic, dentures, impression trays, tools, etc.
- It does not contain acid.
- It can also be used in ultrasonic cleaners.
- The solution is ready to use.
- Do not dilute.
Package:
- 1 liter
Vertex Divosep Blue 5 liters
Vertex Divosep Blue. Preparation for isolating acrylic from gypsum and gypsum from gypsum. Blue for universal use.
Package:
5 l.
Liquid for impregnating plaster models 4.5 l
Product for impregnating and polishing gypsum models. It is perfect for demonstration and orthodontic models.
Directions for use:
Immerse clean and thoroughly dried plaster models in a special solution for 30 minutes.
Remove models, rinse under warm running water. Then dry and polish with a dry, soft cloth. The models treated in this way will have a glossy non-dusting surface.
Package:
4.5 kg
Isolat film 1l
Benefits:
- Heat-resistant, alginate-based insulating agent that forms a thin layer.
- It gives smooth and non-porous surfaces.
- It is suitable for insulating gypsum-gypsum-gypsum, gypsum-silicone.
Package:
- 1l
Plastodur 25ml - preparation for refining plaster stumps
Plastodur a conditioner for plaster stumps.
We apply it with a brush to the surface of the model. It improves the performance of insulators (prevents absorption into the model) and protects against abrasion of contact points when checking the articulation.
Package:
- 25 ml
Isofix DFS gypsum-wax insulator 25 ml
Isofix plaster-wax insulator. Creates a thin film layer of 3-5 microns.
Package:
- 25 ml
Isofix DFS insulator gypsum - wax 500ml
Isofix plaster-wax insulator. Creates a thin film layer of 3-5 microns.
Package:
- 500 ml
DFS Haftspray 75ml spray
Glue for sticking wax elements on the model.
Directions for use:
Possibility to correct the glued elements.
Shake well before use.
Spray distance: 10-15 cm.
Package:
- 75 ml
Kera - Sep spray 75 ml - spray ceramic separator
Spray Seprator. It isolates the porcelain from the plaster model.
Benefits:
- Eliminates the possibility of cross-contamination
- It burns out without residue
- It does not leave stains in the tangential areas
Application:
- Spray the model from a distance of 5 - 8 cm and spray a second time after 1 minute.
- spray the model briefly to avoid streaks.
Package:
- 75 ml.
DFS Preparation for removing the surface tension of wax and silicone
Universal preparation for wax and silicone, based on surfactants before model casting.
Features:
- leaves a smooth surface of the impression and wax model
- evaporates without residue at room temperature
- short drying time
- can be dipped or sprayed
package:
- 500 ml
Iso-stick 1 pc
A practical device for isolating plaster from porcelain and wax.
Advantages:
- Soft and hard tip for individual applications.
- Economical and precise use of insulating material.
- Convenient and easy to use.
- Flexible tip provides excellent insulation in hard-to-reach places.
Isolation = Picosep.
Package:
1 piece
GipEx Tabs Basket for hanging + 2 pcs. tablets - test kit.
- Preparation for a plaster decanter.
- Prevents clogging of drain pipes.
- Reduces unpleasant odors.
- Facilitates cleaning of the clarifier.
Package:
- 2 tablets + a basket for hanging
Fino-Gips-EX U is a plaster remover
For removing any residual gypsum and plaster-bound investment materials, for cleaning alginate or cement residues from impression trays, and for removing dried-on lime deposits from sinks and wash basins. Fully effective in an ultrasonic bath at 35-45 ° C.
Advantages: - Ready-to-use solution; - Optimal effectiveness; - Dissolves heavy soiling.
Packaging:
- 1 piece
Tensio-Sil 1l - preparation for the elimination of surface tension - supplement
Tensio-Sil
preparation reducing the surface tension of impression materials, both alginate and silicones.
Perfect and smooth models after casting.
Package:
- 1000 ml - refill
GipEx decanter tablets 10 pcs.
- Preparation for a plaster decanter.
- Prevents clogging of drain pipes.
- Reduces unpleasant odors.
- Facilitates cleaning of the clarifier.
Package:
- 10 pcs.