Programat S2 is a compact oven designed for sintering caps, frameworks and full contour restorations made of IPS e.max ZirCAD or other zirconium oxide materials at temperatures up to 1600°C. Programat S2 is integrated into the Ivoclar workflow, ensuring optimally coordinated processing steps and consistently high-quality results.

Advantages:

• Optimized cooling shelf provides more space and better cooling.

• New, membrane-sealed keyboard with proven color touch display.

• OSD display extended with the "cooling down" operating status.

• Performance and reliability thanks to software optimization.

• Warranty 2 years

Packaging:

• 1 piece.

The IP Clean Hydro steam generator is a German steam generator with high power and automatic control of the water level in the heating tank. The device recognizes a low water level by itself and draws it from the included 5-liter canister.

• IP Clean Hydro works with ordinary "tap" water and thanks to the filters installed in the canister, the water drawn into the device is clean and descaled.

• A modern heater mounted under a stainless steel tank quickly boils water and generates steam up to 5 BAR. The heater does not have direct contact with water, therefore it is not possible to burn it through too low a water level in the heating tank.

• In IP Clean Hydro, we can use the function of dry and wet steam with a temperature of up to 170C and its pressure can be adjusted with a knob on the front of the device.

• In the case of a calcified heating tank, we can clean it using ordinary citric acid.

Advantages:

• Automatic water intake from a separate canister.
• Always ready to work - the system with a canister allows automatic filling of water while the device is in use.
• Dry and wet steam function.
• Possibility to regulate the pressure of the outgoing steam
• Acoustic signal when the minimum level in the canister is exceeded.
• Casing and boiler made of stainless steel.
• The device has a practical drain screw, which facilitates cleaning and descaling.

Technical data:

• Sizes 24.0 x 35.0 x 38.0 cm.
• Power supply 230V, 50/60Hz.
• 24V handpiece
• Power consumption 1500W
• Tank capacity 4.8L.
• 3-4L reserve tank.
• 5L canister
• Pressure approx. 5 bar.
• Weight 15 kg.
• Steam temperature 170°C

Packaging:

• IP Clean Hydro complete with canister.
• Funnel and pin for hanging the steam gun.

Gasket Gasket for AQUA 4.5L and 7L pressure pot.

Packaging:

• 1 piece

The small and lightweight VP3 easy vacuum pump is a design specifically designed for vacuum generation in Ivoclar porcelain firing furnaces. The diaphragm vacuum pump is characterized by low weight and extremely small dimensions.

Technical data:

• Power supply: 230V / 50-60Hz
• Power Consumption: 70W
• Maximum vacuum: below 40 mbar
• Dimensions: 140 x 130 x 210 mm (W x H x D)
• Warranty 24 months.

Packaging:

• 1 piece.

Electric knife for modeling wax with one tip. Renfert catalog number 21500000

Technical data:

• Dimensions: 91x53x80mm
• Weight: 445g
• Temperature range: 50-200°C
• 36 months warranty.

Advantages:

• Less shrinkage in the modeled element, because the wax does not overheat and does not burn.
• Potentiometer temperature control.
• The handle is made of thermo-insulating natural cork.
• Fast heating and low heat transfer to the handle thanks to the heating element integrated in the tip.

Packaging:

• 1 piece

The Basic Classic sandblaster is the perfect first step into the world of professional sandblasting techniques with feather sandblasters. Compact device in basic configuration with up to 2 tanks. Thanks to its slim design, the sandblaster finds a place even in the smallest space. Two sand tanks, eg filled with 25-70µ 70-250µ sand, cover all standard requirements of dental technology, eg for precious metals and porcelain.

Renfert catalog number 29472025

Advantages:

• Precise work thanks to the unique technology used in the mixing chamber (using the Venturi principle).
• Tool-free expansion to 2 tanks.
• The use of the tank switch located inside the blast chamber ensures efficient operation.
• 36 months warranty

Technical data:

• Mains voltage 220-240 V, 50/60 Hz
• Working pressure 1- 8 bar
• External connection pressure 5-8 bar
• Air consumption at 6 bar (87 psi) 98 l/min
• Lamp power 16W
• Cord length 2m
• Dimensions (W x H x D) 350 x 270 x 470 mm
• Sand blasting chamber size 14 l
• Capacity of 1 tank 1000 ml
• Weight (unfilled) 6.5 kg

Packaging:

• 1 piece.

Spirit burner.

Package:

1 piece

MicroTorch Type I Torch

Characteristics:

• Once filled, it lasts for 60 minutes of continuous use.
• For use in the dental and prosthetic office.
• Refillable with lighter gas (propane-butane)
• Easy to use.
• Achievable temp. 1300 °C
• 3 months warranty.

Packaging:

• 1 piece.

• The stainless steel AQUA pressure pot is ideal for the homogeneous and bubble-free polymerization of acrylic materials.

Technical data:

• Diameter (inside): 220 mm
• Height (inside): 110mm
• Capacity: approx. 4.5 liters
• Working pressure: 2.0 bar
• Working overpressure: max. 2.2 bar
• Operating temperature: max. 55°C
• Weight: 2.2 kg
• 12 months warranty

Packaging:

• 1 piece

The stainless steel AQUA pressure pot is ideal for the homogeneous and bubble-free polymerization of acrylic. The huge capacity of this pot provides space for all standard articulators, thus, for example, orthodontic splints can be produced directly on the models in the articulator.

Technical data:

• Diameter (inside): 220 mm
• Height (inside): 210mm
• Capacity: approx. 7 liters
• Working pressure: 2.0 bar
• Working overpressure: max. 2.2 bar
• Operating temperature: max. 55°C
• Weight: 2.6 kg
• 12 months warranty.

Packaging:

• 1 piece

Plaster sedimentation tank with compartments.

Characteristics:

• Partitions enable any connection of the settling tank to the sewage system.
• It is only necessary to remember about the cascade principle (water overflowing into successive and lower chambers) for the device to fulfill its function.
• After the partitions are properly set, the settling tank should be tightly closed.
• Effectively protects the sewage system against all waste heavier than water, such as gypsum, investment compounds, etc.
• Necessary, EU regulations oblige all renovated and newly built dental technology laboratories to install devices that filter heavy waste such as gypsum, investment materials, etc.
• We attach the certificate of conformity needed for Sanepidu.

Information:

• Four overflow chambers.
• Tight closure.
• Standard '50 connections.
• Full freedom of positioning the inlet and outlet pipes.
• Operation and assembly instructions.
• Soft plastic dividers for easy cleaning.
• CE certificate for Sanepid.
• Very easy to clean.
• Resistant to low and high temperatures.
• 5 years warranty.

Technical data:

• Height 32 cm.
• Height of the filler pipe connection 38 cm.
• Diameter 32 cm.
• The height of the spout pipe is 18 cm from the base.

Packaging:

• 20l bucket.

NEW!!! Wet cutter with work light and aqua stop.

Renfert catalog number 18070000

Advantages:

• Efficient and precise wet trimming of plaster dental models.
• Work without fatigue thanks to integrated work lighting.
• Reduce costs and protect resources thanks to the aqua stop function.
• Quickly adjust the angle of the cutter table using the handy tilt mechanism (90°/98°).
• Easy and quick cleaning thanks to the disassembly of the cutter table, door and spray pipe without tools.
• Clean, interference-free operation thanks to optimal sealing.
• 36-month warranty.

Technical data:

• Permissible mains voltage 220–240 V
• Permissible mains frequency 50/60 Hz
• Power consumption 1300 W (230 V)
• Motor capacity (P1) 1300 W
• Motor capacity (P2) 900 W
• Rotational speed 2880–3400 rpm
• Water consumption max. 7 l/min
• Water pressure min. / max. 1–5 bar
• Ø (Connection piece for drain hose) 36 mm
• Ø (cutting disc) 234 mm
• Dimensions (W x H x D) 305 x 330 x 410 mm
• Weight (without cutting disc) ~13.2 kg

Packaging::

• Klettfix disc cutter

NEW!!! Wet cutter with work light and aqua stop.

Renfert catalog number 18070500

Advantages:

• Efficient and precise wet trimming of plaster dental models.
• Fatigue-free working thanks to the integrated work light.
• Cost reduction and resource conservation thanks to the aqua stop function.
• Quickly adjust the angle of the trimmer table with the handy tilt mechanism (90°/98°).
• Easy and quick cleaning thanks to tool-free removal of the cutting table, door and spray tube.
• Clean, interference-free operation thanks to optimal sealing.
• 36 months warranty.

Technical data:

• Permissible mains voltage 220-240 V
• Permissible mains frequency 50/60 Hz
• Power consumption 1300W (230V)
• Motor capacity (P1) 1300 W
• Motor output (P2) 900W
• Rotation speed 2880-3400 rpm
• Water consumption max. 7 l/min
• water pressure min. / max. 1-5 bar
• Ø (connection piece for drain hose) 36 mm
• Ø (cutting disc) 234 mm
• Dimensions (W x H x D) 305 x 330 x 410 mm
• Weight (without blade) ~13.2 kg
• Marathon dial (partly diamond-coated)

Packaging::

• Marathon cutter

NEW!!! Set with extension for orthodontics for MT premium

Advantages:

• Quickly and precisely trim orthodontic models using an intuitive template and a special trimmer table.
• Greater precision and optimal positioning of the mid palatal suture thanks to the use of a guide light (MT premium only).
• Producing accurate 3D models of the jaws that take into account all planes of the skull.
• Thanks to the special guide concept, the template is not fixed in the device and can therefore be easily removed without tools.
• Easy, quick and tool-free cleaning of all components.
• Step-by-step instructions with reference models of the upper jaw and lower jaw (also suitable for process documentation).

Technical data:

• Power consumption 150mW
• Dimensions (W x H x D) 25 x 42 x 115 mm
• Weight ~40g
• Laser class 1

Packaging:

• ORTHO MT premium guide set

Hotty LED wax melter.

Renfert catalog number 14610000

Characteristics:

• Fast and precise cap making.
• Very small temperature fluctuations guarantee the production of caps of a certain thickness.
• The temperature is entered via a foil-covered keypad and displayed on an LED display.
• 3 years warranty

Packaging:

• 1 piece.

• Keystone spirit burner.

Advantages:

• The wick is durable and maintains a steady flame.
• Made of durable plastic.

Packaging:

• 1 piece.

The best in every way. When high-quality tools are required, there is no alternative to the KaVo KPOWERgrip.

Advantages

• Micro motor with exceptionally high torque (up to 7 Ncm) guarantees full versatility of work in all conditions and with any materials.
• The noiseless and vibration-free operation of the induction motor promotes concentration at work.
• The reduced weight of the handpiece and the ultra-flexible cable allow freedom of action when performing prosthetic works.
• The modern, specially developed grip surface for the KPOWERgrip guarantees a comfortable and secure grip of the handpiece.
• 12 months warranty.

Characteristics:

• 20% more efficient cooling.
• Modern construction technology guarantees reduced heating of the handpiece.
• Secure and stable grip of the tool during work.
• A completely new cover has been developed for the K-POWERgrip to make it easier to work properly.
• More power in every situation.
• The new micromotor has increased power and torque.
• More freedom while working.

Technical data:

• Rotation range 1.000 - 50.000 rpm
• Max torque 7Ncm
• Drive without brushed DC motor
• Power on the cutter 150 W

Packaging:

• 1 piece.

Electropolisher ST2 for electrolytic polishing of dentures made of prosthetic acid-resistant steel, manufactured in cooperation with Prodento-Optimed, in a version with an electronic clock with a LED display.

Technical data:

• Polishing current: 0.5-4.0 A
• Electrolyte container: 0.8 dm3
• Time setting range: minute mode 99 min + 59 s
• Power supply: 220V / 50-60Hz
• Max power consumption: 80W
• Dimensions: (W x D x H): 240 x 250 x 95 mm
• Weight: 2.10 kg
• 12 months warranty

Packaging:

• 1 piece

Widia nozzle for the Sandblast stationary sandblaster

Package:

• 1 piece.

Porcelain kiln calibration test.

• For Programat ® P200, P300, P310, Programat X1, etc.

Packaging:

• 10 silver stamens.
• 2 coasters.

PR-3 manual press

• Available in green.

Application:

• It is mainly used for precise and quick molding of the mass in gypsum matrices of polymerization cans due to the high force of manual pressure of the twisted screw.

Technical data:

• pressure max. - 500 kg
• Curb weight - 13 kg
• Capacity - 3 polymerization cans

Packaging:

• 1 piece.

Silent TS 2 prosthetic lift. Highly efficient, quiet and compact. Possibility of independent control of two stations. Can be used as an extractor for devices and workstations. With multi-function LCD display, adjustable suction power. Auto diagnosis function.

Renfert part number: 29300050

Characteristics:

• Low noise level only 52-61 dB(A).
• Simple operating concept.
• Thanks to its compact design, it does not take up much space.
• Large bag capacity (approx. 7.5 l).
• Easy filter bag change from the front.
• Very clean, dust-free removal of filter bags (lockable).
• The Silent TS2 switches on with a pre-set suction level, opening the appropriate of the two usable valves, e.g. when one micromotor is activated. When the second device (the second person) starts to work, the second valve is opened and the motor power is automatically adjusted to the pre-set suction level, so that it is the same in both channels. When one of the two users stops working, the Silent TS2 continues to run for a pre-programmed time, after which it automatically closes the corresponding valve. The motor power automatically decreases to the previously set suction power.

Technical data:

• Dimensions - 595 x 225 x 565 mm
• Power - 230V, 50/60Hz.
• Power consumption 1400W
• Connection value of the device socket max. 2000W
• Suction port int. 32.5mm, ext. 40.0mm.
• Suction power 55 l/sec.
• Weight 21 kg.
• 36 months warranty.

Packaging:

• Silent TS2, 4 m suction hose, 4 PVC end couplings

Star steam generator device producing saturated steam. The high pressure of 4 bar and a temperature of 150 ° C enables excellent cleaning of various objects or e.g. wax residues on models, dirt in inaccessible work areas, or soldering residues. Grease, sticky wax, solvents and plaster residues are gently and quickly removed without chemical additives.

Advantages:

• Adjustment of the degree of humidification and steam pressure.
• Corrosion-resistant tank made of stainless steel.
• No water connection required thanks to manual filling.

Technical data:

• Power supply 230/50Hz.
• Power consumption 1100W
• Working pressure 0-4 bar.
• Tank capacity 3.5L
• Weight 8 kg.
• Dimensions WxHxD)) 280 / 290 + 40 / 330 mm.
• Manual filling.
• 12 months warranty.

Packaging:

• 1 piece.

Working chamber specially designed for machining materials that require a water jacket, such as zirconium.

Advantages:

• Waterproof LED lighting guarantees excellent visibility.
• Stainless steel housing with a wide field of view.

• handpiece adapter.

• Optionally, it can be purchased with a pedal activating the drainage of accumulated water.

Technical data:

• Power: 26W
• Dimensions: 260/460/370+50mm
• Weight: 8 kg

Packaging:

• 1 piece

Erkoform 3D + is a device for vacuum deep-moulding.

Characteristics:

• Temperature measurement sensor.
• Touch panel with menu in Polish.
• Does not require connection to the compressor.
• Before pressing, a vacuum is created immediately.
• No preheating required.
• Vertical foil stamping guarantees even thickness of the work performed.
• Easy access to the model during heating.
• Plenty of space for tall models.
• Telescopic and tilting film application.
• Practical, one-handed clamping of foils up to 5 mm thick.

Technical data:

• Dimensions - 37.0 x 35.0 x 31.5 cm.
• Power - 230V/50Hz; 340W
• max. vacuum 0.8 bar.
• Noise < 70dB(A).
• Weight 11.9 kg.
• 12 months warranty

Packaging:

• Erkoform-3d+, film trial pack, film retaining ring, granulate collecting device, model plate, granulate container, granulate filling brush with rubber cap, on-off magnet, power cable, white working tray, filling pellets, machine documentation ( folder)

Bijou 90 table lab burner.

Renfert catalog number 9600000

Characteristics:

• The required flame intensity can be infinitely selected between the main flame and the economy flame.
• The oxygen supply is regulated by setting rings on the chimney.
• Each burner, apart from the vertical position, can be tilted to each side by 30 degrees.
• This prevents dripping wax from clogging the nozzle. The burner with non-tilting base can be easily disconnected.
• Propane - butane gas burner.
• 3 years warranty.

Packaging:

• 1 piece.

Reliable water softening and filtering system, specially adapted to the POWER 2 steamer. The system provides optimal protection for the POWER steamer, increasing its efficiency, reliability and durability.

Renfert catalog number 18460100

Advantages:

• Affordable and advanced water softening/filtering technology that is usually only available in large and expensive systems.
• It supplies the POWER 2 evaporator with clean, calcium-reduced water.
• Easy, compact installation (free-standing or wall-mounted) that can be completed in minutes.
• Simple operation and monitoring (visual and acoustic signal) using a flow sensor with an OLED display.
• Quick replacement of filter cartridges in seconds - remove, insert, that's it.
• Durable filter cartridges.
• Venting and rinsing directly at the filter head, without disconnecting the pipes (using automatic inlet and outlet shut-off valves).
• Automatic replacement of all gaskets between head and cartridge with each cartridge change.

Packaging:

• POWER Steamer water softener, filter head with rinsing hose, rinsing hose, connection hose, 2 adapters 3/4" - 3/8", gaskets, M filter insert for POWER steamer softener, flow meter for POWER steamer softener, user manual/ Quick Start Guide, test strips for determining water hardness

Polishing spindle.

Characteristics:

• On request, we order a spindle to be made on the model of a used one, the lead time is about 7-14 days.

Packaging;

• 1 piece.

• Pressure polymerizer designed for technical and dental laboratories.
• Made of stainless steel INOX with a pressure gauge, it is perfect for polymerization of acrylic masses.
• In particular for: repairs, temporary crowns, removable orthodontic appliances, parts of acrylic frame dentures.
• Thickened bottom
• Separate exhaust valve
• Safe lid opening and closing mechanism

Benefits:

• Protection against uncontrolled pressure increase
• Sufficient space for the articulator
• Suitable for polymerization of most acrylic masses

Technical data:

• Capacity 7 liters
• Max temperature (°C) - 65°C
• Max pressure (bar) - 2 bar
• Inner diameter 22cm
• Inner height 21cm
• Weight (kg) - 3.2 kg
• 12 month warranty (does not include gasket)

Packaging:

• 1 piece

• Cover for the polisher made of powder-coated sheet metal, with a plastic removable cuvette.

Packaging:

• 1 piece

• Spirit burner wick.
• Length 15cm.

Packaging:

• 1 piece.

• Allows you to connect dust extraction at the workplace.
• Renfert catalog number 29250000

Benefits:

• solid beech wood mount.
• secure attachment to a 20-40 mm thick workbench.
• suction hose connection on the right or left side.
• removable sieve to prevent accidental suction of elements from the table.
• detachable suction part.

Technical data:

• diameter of the suction hose connection 40 mm.

Additional equipment:

• protective glass. - To be ordered separately (mikran number 1859)

Packaging:

• 1 piece without glass.

• Manifold and connectors for the extractor.
• Allows you to extract dust from 2 devices at the same time.
• Renfert catalog number 29260000

Packaging:

• Extractor diverter with 4 sockets (without hose)

• Protective glass for the lift hoof
• Renfert catalog number 29251000

Packaging:

• 1 piece (window only without suction tip)

-Precise device for cutting plaster models. - Equipped with an extractor that removes gypsum particles created during segmentation. - Electromagnetic table, moved in all planes, allows for optimal positioning of the model and obtaining the highest stability and precision during work.

• Warranty 3 years.

Technical data:

• Power: 100W
• Rotation: 2800 / min
• Diamond blade: 80 x 16 x 0.2 mm
• Dial thickness: 0.25 mm
• Dimensions: 21 x 26 x 40 cm
• Weight: 10.5 kg

Packaging:

• 1 piece

• Waxorofi dish.
• Renfert catalog number 14400000

Technical data:

• Dimensions 7.8x12.0x5.4 cm
• Wax heater capacity 110 ml

Benefits:

• individual wax consistency setting (from creamy to liquid)
• ideal processing temperature - this way overheating of the wax is avoided;
• extremely low shrinkage of prosthetic waxes;
• high precision when setting the teeth;
• time saving;
• stepless temperature control 40-110 °C;
• large bowl for melting approx. 4 wax plates, with a wax scraper on the inner edge of the bowl.

Packaging:

• 1 piece.

• Power STEAMER I - a novelty on the market.
• Renfert catalog number 18450000

Advantages:

• Flexible location selection with manual filling.
• The heater is built into the boiler wall, which prevents limescale deposits on it and prevents it from burning out due to too little water in the tank.
• High operational reliability thanks to real-time calcification rate.
• Easy cleaning of the pressure tank thanks to the extra-large service opening.
• Continuous and effective cleaning performance thanks to the power of up to 2000 W and the working pressure of 4.5 bar combined with the innovative technology of steam nozzles.
• Safe and comfortable steam cleaning thanks to the ergonomic handle (the housing safely discharges the electrostatic charge).
• Wall mounting possible with optional wall bracket.

Technical data;

• Permissible mains voltage - 220-240 V
• Permissible mains frequency - 50/60 Hz
• Power consumption - 2000 W
• The volume of the pressure tank - 4 l
• Volume (recommended filling amount) - 2.8 l
• Volume (maximum filling amount) - 3 l
• Working pressure - 4.5 bar
• Dimensions (W x H x D) - 370 x 422 x 350 mm
• Weight (empty) - ~9.5 kg
• 36 months warranty

Packaging:

• 1 steam cleaner,
• 1 tank cap,
• 1 quick start guide,
• 1 service plug tool,
• 1 sealing kit

Power STEAMER II - Steam generator with automatic filling. New on the market. It is recommended to buy a Power steamer water softner for the device (mikran number 1451)

Renfert catalog number 18460000

Advantages:

• The heater is built into the boiler wall, which prevents limescale deposits on it and prevents it from burning out due to too little water in the tank.
• Thanks to the mains water connection and the integrated pump, the pressure tank is filled automatically and ensures that steam is always available.
• High operational reliability and reliability with real-time calcification rate.
• Easy cleaning of the pressure tank thanks to the extra-large service opening.
• Continuous and effective cleaning performance thanks to the power of up to 2000 W and the working pressure of 4.5 bar combined with the innovative technology of steam nozzles.
• Steam available at all times - even during intensive continuous operation - thanks to automatic filling via mains water connection and integrated pump.
• Optimum control by displaying the current operating pressure via a pressure gauge.
• Significantly reduce the amount of effort required for rinsing, cleaning and descaling the pressure tank thanks to the effective rinsing program.
• Safe and comfortable steam cleaning thanks to the ergonomic handle (the housing safely discharges the electrostatic charge).
• Easy to fill with water and descaling thanks to the handy funnel-shaped refills.
• Wall mounting possible with optional wall bracket.

Technical data:

• Permissible mains voltage - 220-240 V
• Permissible mains frequency - 50/60 Hz
• Power consumption - 2000 W
• The volume of the pressure tank - 4 l
• Volume (recommended filling amount) - 2.8 l
• Volume (maximum filling amount) - 3 l
• Working pressure - 4.5 bar
• connection pressure. - 1-5 bar
• Dimensions (W x H x D) - 370 x 422 x 350 mm
• Weight (empty) - ~10.1 kg.
• 36 months warranty.

Packaging:

• 1 steam cleaner
• 1 tank cap
• 1 quick start guide
• 1 service nut tool
• 1 sealing kit

• Power Steamer I and II steam generator descaler is the perfect solution for effective and gentle descaling.
• Renfert catalog number 18450100

Benefits:

• Descaling that is both effective and gentle on the material - the formula is specially adapted to the aluminum pressure tank (including corrosion protection).
• Descaling much faster than standard commercial descaling solutions.

Step by step:

• Unplug the device and let it cool down
• Rinse the pressure tank with water and a cleaning brush
• Close the service hole
• Fill the pressure tank with 1 liter of water and then add 1 liter of Renfert POWER descaler
• After 15 minutes, add another 0.6-0.8 l of water. If foam appears, continue filling only after the foam has subsided
• Leave the descaling solution for 2-4 hours for light soiling and 8-14 hours for heavy soiling.
• Open the service port and drain the descaling solution
• The used descaling solution can be poured down the drain if it is highly diluted
• Rinse the pressure tank several times with water and clean with a brush

Packaging:

• 1l

Benefits:

• Prosthetic Air Turbine
• Built-in dust protection system
• Speed 320,000 min-1
• Smooth speed control
• High torque
• Low vibration and noise levels
• Deviation of the drill from the axis during operation less than 0.02 mm
• 12 months warranty.

Packaging:

• 1 piece.

The polisher with a particularly robust construction has a motor shaft that rotates on ball bearings.

Advantages:

• High power allows for a better finish of the model.
• The device has a safety switch
• Polisher supplied with right and left tips.
• The design of the motor also allows for self-ventilation. In this way, it is possible to work for a long time without overheating.

Technical data:

• Power supply: 230V / 50Hz
• Power: 170 / 400W
• Engine speed: 1400 / 2800 rpm
• Dimensions: 36x21x26h cm
• Weight: 10kg
• 5 years warranty

Packaging:

• 1 piece

• Possibility of using from 1 to 3 cans, simple in construction and reliable.
• Great aesthetics.

Technical data:

• maximum pressure: 15000 kg
• usable pressure: 200 bar
• max pressure: 400 bar
• max. table width: 11cm
• piston stroke: 1.6 cm
• usable height: 23.5 cm
• usable width: 12cm
• capacity: 3 large polymerization cans
• external dimensions: width 22cm x depth 19cm x height 48cm
• weight: 20kg.
• warranty 12 months

Packaging:

• 1 piece

Detailed information:

• Dental tech. Damian Dunajewski Consultant/CAD/CAM Specialist Tel.600 128 010 damian.dunajewski@mikran.com
• Dental tech. Kamil Wolniewicz Consultant/CAD/CAM Specialist Tel.530 596 166 kamil.wolniewicz@mikran.com

Advantages:

• Full arc scan - 12 sec.
• Accuracy 8 microns.
• Very good scanning of models with hard-to-reach places.
• Orthodontic models.
• Undivided models.
• True color texture scanning in color.
• Wide range of applications (veneers, implants, unsplit models, split models, impressions.
• Scanning the model in true color.
• Impression scanning.
• Scanning unsplit models.

Functions:

• All-in-one scanning
• One-click triple tray scanning.
• Impression scanning.

Technical data:

• Model size 355×268×384（mm)
• Weight 9.5 kg
• 2x1.3mp cameras.
• Accuracy 8 microns.
• Blue light projector, multi-color scanning.
• USB 3.0 interface
• Output format STL；UM；PLY；OBJ
• Power supply AC110-240V (50HZ)
• 12-month warranty.

The scanner price does not include software:

Packaging:

• 1 piece

• MT Plus trimmer with Klettfix blade
• Renfert catalog number 18030000

Characteristics:

• Easy processing of even the hardest plaster models.
• For wet and dry use when connected to an extractor.

Technical data:

• Power supply 230/50Hz, 6A
• P1 output power: 1300W
• P2 output power: 900W
• Rotation 2820 1/min.
• water consumption max. 9 l/min.
• Minimum water pressure 1 bar for a flow rate of 6 l/min.
• 2m power cord.
• Diameter of the water outlet 35 mm.
• Water outflow length max. 1.5m
• Diameter of the suction element int. 29mm, ext. 35-40mm.
• Weight approx. 12.7 kg.
• Dimensions (WxHxD) 298x318x412mm.
• The noise level meets DIN 45635-01-KL3 74 dB(A).
• 36 months warranty

Packaging:

• 1 piece.

Electropolishing cables

Packaging:

• 2 pcs

The Foredom Lighted Work Chamber MALC15 dust cover is designed for smaller prosthetic, laboratory, jewelry, carving or other technical work that does not require much space. It offers excellent visibility and cleanliness while working on processes such as grinding, polishing and drilling. A pressurized nozzle with adjustable airflow helps clean workpieces and directs dust to the exhaust.

Advantages:

• LED lighting.
• 2x magnifying glass with additional 10x magnification.
• Nozzle for connecting compressed air up to 90 PSI or 6 bar with adjustable flow.
• Plexiglass splash guard.
• Magnetic base.
• Comfortable armrests.
• Connection for connecting the extractor.
• 2-pin connector for extractor on/off control.
• Warranty 24 months.

External dimensions:

• Height 29 cm.
• Width 28 cm.
• Depth 25 cm.

Internal dimensions: - Height 20 cm. - Width 26 cm. - Depth 16.5 cm.

Libra:

• 5 kg without packaging.
• 7 kg with packaging.

Packaging:

• 1 piece

DDphoeniX is a powder to help clean soiled sintering ovens. Regular use minimizes the problem of discoloration, thus extending the life of the heaters.

• Sintering - cleaning program - as recommended by the furnace manufacturer.
• Thorough cleaning (in case of problems with the color of works) 30--50 gr X 2 cleaning cycles.
• Regular cleaning (every 2 weeks) approx. 30gr x 1 cleaning cycle.

Precautions:

• When using the powder, use protective gloves and a mask to protect the eyes and mouth.
• Do not eat or drink while using the powder.
• Avoid breathing dust.
• Apply to the sinter tray at a distance and at moderate speed to avoid increased dusting.

Storage:

• Keep tightly closed in the original packaging.
• Store in a cool, dry place.

Packaging:

• 1pc/200g

• One device for all materials

• The Perfecta 900 can be connected to a motor with a high-speed handpiece and a motor with a technical handpiece at the same time, which allows you to process all materials with just one device.

• Based on decades of experience, W&H has developed a prosthetic motor that offers the world's first integrated handpiece blow-off function.

Technical data:

• Motor with high-speed handpiece 0.7 Ncm, 5,000 - 100,000 rpm
• Brushless motor
• Diameters of rotary instruments 1.6
• Blow-off function
• Bistable / Cruise control automatic programs
• Turns right and left
• Tabletop version with foot control / Knee version
• External additional controller (optional with foot device)
• Warranty 24 months

Packaging:

• 1 piece.

• The new high-torque micromotor guarantees stable operation in the full speed range from 1,000 to 35,000 rpm,
• Effective soundproofing combined with other features allows you to meet high requirements when performing prosthetic works.
• The K5plus weighs only 200 g. Thanks to its ergonomic shape, ultra-thin cable, quiet operation and low weight, the operator's work is secure and comfortable.

Technical data:

• Rotation range 1.000 - 35.000 rpm
• Max torque 4.5Ncm
• Cutter size 2.35mm, 3.00mm, 1/8
• Taper 0.02mm
• Cooling, no additional cooling required
• Drive, brushless DC motor
• The shape of the handle, designed in accordance with the principles of ergonomics
• 12 months warranty

Packaging:

• 1 piece.

Our DUNAFORM PLUS pressure molding device is a new generation device.

Advantages:

• Menu driven and user friendly service.
• Large and clear display.
• Fixed press programs + 10 freely programmable memory locations.
• Time information is provided visually and acoustically.
• There is no need to preheat, the shortwave infrared heater will instantly set the desired temperature.
• The foil is heated with the side facing the model.
• Possibility of embossing foil with a diameter of 120 mm and 125 mm.
• Almost all commercially available foils can be used in this way.

Technical data:

• Electric power supply: 230V/50Hz.
• Power : 850W
• Weight: approx. 8.5 kg.
• Width: 350mm.
• Depth: 300mm.
• Height: 190mm.

Packaging:

• 1pc device + trial set of film and 2 kg of granulate.